Mazda 6. Manual — part 321
T–44
EXTERIOR LIGHTING SYSTEM
BACK-UP LIGHT SWITCH INSPECTION
A6E811217640W02
1. Disconnect the back-up light switch connector.
2. Inspect for continuity between the back-up light
switch terminals using an ohmmeter.
• If not as specified, replace the back-up light
switch.
End Of Sie
FLASHER UNIT REMOVAL/INSTALLATION
A6E811266830W01
1. Disconnect the negative battery cable.
2. Remove the instrument cluster. (See
T–72 INSTRUMENT CLUSTER REMOVAL/INSTALLATION
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
FLASHER UNIT INSPECTION
A6E811266830W02
1. Connect the connector to the flasher unit.
2. Connect the negative battery cable.
3. Measure the voltage at the flasher unit using voltmeter.
• When inspecting terminal F for continuity, disconnect the flasher unit connector.
4. If the value are not as specified in the Terminal Voltage List (Reference), inspect the parts under “Action” and
related wiring harnesses.
5. If the system does not work properly even though the parts or related wiring harnesses do not have any
malfunction, replace the flasher unit.
A6E8112W153
A6E8112W128
1
Connector
2
Screw
3
Flasher unit
A6E8112W114
EXTERIOR LIGHTING SYSTEM
T–45
T
Terminal Voltage List (Reference)
End Of Sie
RUNNING LIGHT UNIT REMOVAL/INSTALLATION
A6E811266731W01
1. Disconnect the negative battery cable.
2. Remove the glove compartment. (See
S–85 GLOVE COMPARTMENT REMOVAL/INSTALLATION
)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
A
Power supply
HAZARD 10 A
fuse
Under any condition
B+
• Inspect HAZARD 10 A
fuse
• Inspect related harness
D
Turn signal
flasher (LH)
Turn signal light
(LH)
Turn signal light (LH) flashes
Alternates
below 1.0 and
B+
• Inspect turn signal light
(LH)
• Inspect related harness
Hazard warning switch at on
position
Other
Below 1.0
F
Flasher unit
ground
GND
Constant: inspect for
continuity to ground
Yes
• Inspect GND
G
Turn signal
flasher (RH)
Turn signal light
(RH)
Turn signal light (RH) flashes
Alternates
below 1.0 and
B+
• Inspect turn signal light
(RH)
• Inspect related harness
Hazard warning switch at on
position
Other
Below 1.0
H
Hazard warning
on
Hazard warning
switch
Hazard warning switch at on
position
Below 1.0
• Inspect hazard warning
switch
• Inspect related harness
Hazard warning switch at off
position
B+
I
Turn switch on/
off (RH)
Combination
switch
Ignition switch is at ON and
turn switch (RH) on
B+
• Inspect combination
switch
• Inspect related harness
Other
Below 1.0
J
Turn switch on/
off (LH)
Combination
switch
Ignition switch is at ON and
turn switch (LH) on
B+
• Inspect combination
switch
• Inspect related harness
Other
Below 1.0
A6E8112W154
1
Nut
2
Running light unit
3
Connector
A6E8112W126
T–46
EXTERIOR LIGHTING SYSTEM
RUNNING LIGHT UNIT INSPECTION
A6E811266731W02
1. Connect the connector to the running light unit.
2. Connect the negative battery cable.
3. Measure the voltage at the running light unit using voltmeter.
• When inspecting terminal D, H or P for continuity, disconnect the running light unit connector.
4. If the value are not as specified in the Terminal Voltage List (Reference), inspect the parts under “Action” and
related wiring harnesses.
5. If the system does not work properly even though the parts or related wiring harnesses do not have any
malfunction, replace the running light unit.
Terminal Voltage List (Reference)
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
A
Illumination
light on/off
TNS relay
Ignition switch at ON position
B+
• Inspect ILLUMI 10 A
fuse
• Inspect TNS relay (See
• Inspect related harness
Ignition switch
at LOCK or
ACC position
Headlight switch
(light) at TNS or
headlight
position
Below 1.0
Headlight switch
(light) at OFF
position
B+
B
Illumination
light operation
• Instrument
cluster
• Panel control
switch
Headlight switch (light) at TNS or
headlight position
B+
—
Headlight switch (light) at OFF
position
Below 1.0
C
Headlight
relay (high-
beam) on/off
Headlight relay
Ignition switch at ON position
B+
• Inspect headlight relay
• Inspect related harness
Headliht switch
(light) at
headlight
position
Headlight switch
(dimmer) at LO
position
B+
Headlight switch
(dimmer) at HI
position
B+
Flash-to-pass on
B+
D
Running light
unit ground
GND
Under any condition: inspect for
continuity to ground
Yes
• Inspect GND
E
IG1
METER IG 15 A
fuse
Ignition switch at ON position
B+
• Inspect METER IG
15 A fuse
• Inspect related harness
Ignition switch at LOCK or ACC
position
Below 1.0
F
Front fog light
relay on/off
Front fog light
relay
Front fog light
switch at ON
position
Headlight switch
(light) at TNS or
headlight
position
Below 1.0
• Inspect TNS relay (See
• Inspect front fog light
relay (See
• Inspect related harness
Headlight switch
(light) at OFF
position
B+
G
TNS relay on/
off
TNS relay
Ignition switch at ON position
Below 1.0
• Inspect TNS relay (See
• Inspect related harness
Ignition switch at LOCK or ACC
position and headlight switch
(light) at OFF position
B+
A6E8112W155
EXTERIOR LIGHTING SYSTEM
T–47
T
End Of Sie
H
Front fog light
on/off
Front and rear
fog light switch
Front and rear fog light switch at
OFF position: inspect for continuity
to ground
No
• Inspect front and rear
fog light switch (See
42 FRONT AND REAR
FOG LIGHT SWITCH
INSPECTION
• Inspect related harness
Front and rear fog light switch at
ON position: inspect for continuity
to ground
Yes
I
TNS on/off
Headlight switch
Headlight switch (light) at OFF
position
No
• Inspect headlight
• Inspect related harness
Headlight switch (light) at TNS or
headlight position
Yes
K
Headlight
relay on/off
Headlight relay
Ignition switch at ON position
Below 1.0
• Inspect headlight relay
• Inspect related harness
Ignition switch at LOCK or ACC
and headlight switch (light) at OFF
position
B+
M
Flash-to-pass
on/off
Headlight switch
(dimmer switch)
Headlight switch (light) at OFF or
TNS position
No
• Inspect headlight
• Inspect related harness
Headlight switch (light) at headlight
position
Yes
Flash-to-pass on
Yes
O
Headlight
high
operation
Headlight switch
(dimmer switch:
HI position)
Ignition switch at ON position
B+
• Inspect headlight
• Inspect related harness
Headlight switch (light) at headlight
position and headlight switch
(dimmer) at LO position
B+
Headlight switch (light) at headlight
position and headlight switch
(dimmer) at HI position
Below 1.0
Flash-to-pass on
Below 1.0
P
Headlight
(high-beam)
on/off
Headlight switch
Headlight switch (dimmer) at LO
position: inspect for continuity to
ground
No
• Inspect headlight
• Inspect related harness
Headlight switch (dimmer) at HI
position: inspect for continuity to
ground
Yes
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст