Mazda Protege 5. Manual — part 329
SUNROOF
09–15–13
09–15
5HB
Motor
1. Remove the sunroof motor.
2. Apply battery positive voltage to the sunroof
motor terminals and inspect the operation of the
sunroof motor.
•
If not as specified, replace the sunroof motor.
Limit Switch
1. Remove the headliner. (See 09–17–16 HEADLINER REMOVAL/INSTALLATION.)
2. Verify the glass panel position.
3. Disconnect the connector.
4. Inspect for continuity between the sunroof motor
terminals using an ohmmeter.
•
If not as specified, replace the sunroof motor.
End Of Sie
Connection
Motor operation
1A
1I
B+
GND
Turn right (Slide open/Tilt down)
GND
B+
Turn left (Slide close/Tilt up)
A3U0915W017
A3U0915W019
A3U0915W018
1712-1U-01G(09-15).fm 13 ページ 2001年6月29日 金曜日 午前10時33分
SUNROOF
09–15–14
SUNROOF RELAY REMOVAL/INSTALLATION
A3U091569873W01
4SD
Note
•
Sunroof relay is built in the sunroof motor.
5HB
1. Disconnect the negative battery cable.
2. Remove the headliner. (See 09–17–16 HEADLINER REMOVAL/INSTALLATION.)
3. Pull the sunroof relay from the sunroof frame.
4. Disconnect the connector, and remove the
sunroof relay.
5. Install in the reverse order of removal.
End Of Sie
SLIDING SUNROOF SYSTEM WIRING DIAGRAM
A3U091501049W02
4SD
A3U0915W020
A3U0915W027
1712-1U-01G(09-15).fm 14 ページ 2001年6月29日 金曜日 午前10時33分
SUNROOF
09–15–15
09–15
5HB
End Of Sie
A3U0915W026
1712-1U-01G(09-15).fm 15 ページ 2001年6月29日 金曜日 午前10時33分
SUNROOF
09–15–16
SUNROOF RELAY INSPECTION
A3U091569873W02
4SD
1. Remove the headliner. (See 09–17–16 HEADLINER REMOVAL/INSTALLATION.)
2. Connect the sunroof switch connector.
3. Connect the negative battery cable.
4. Measure the voltage at the sunroof relay terminals as indicated below.
5. Disconnect the sunroof relay connector before inspecting for continuity at terminal 1F.
•
If not as specified, inspect the parts listed under “Action” and the related wiring harnesses.
•
If the parts and wiring harnesses are okay but the system still does not work properly, replace the sunroof
relay.
Terminal voltage list (Reference)
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
1A
IG2
Sunroof motor
IG SW is at ON position.
B+
•
Inspect A/C 15 A fuse
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect related harness
Other
0
1B
Tilt up
Sunroof switch
Sunroof is tilting up. (Including
position when fully closed)
B+
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect related harness
Other
0
1C
Slide close
Sunroof switch
Sunroof is closing. (Including
position when fully closed and
open)
B+
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect related harness
Other
0
1D
Slide open
Sunroof switch
Sunroof is fully opening.
0
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect related harness
Other
B+
1E
Tilt down
Sunroof switch
Sunroof is tilting down. (Not
including position when fully
closed)
B+
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect related harness
Other
0
1F
Sunroof relay
ground
GND
Under any condition: inspect
for continuity to ground.
Yes
•
Inspect related harness
2A
Slide close/
tilt up
Sunroof motor
Sunroof is opening/tilting
down.
0
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect sunroof motor
(See 09–15–12 SUNROOF
MOTOR INSPECTION)
•
Inspect related harness
Sunroof is closing/tilting up.
B+
Other
0
2B
Slide open/
tilt down
Sunroof motor
Sunroof is opening/tilting
down.
B+
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect sunroof motor
(See 09–15–12 SUNROOF
MOTOR INSPECTION)
•
Inspect related harness
Sunroof is closing/tilting up.
0
Other
0
A3U0915W023
1712-1U-01G(09-15).fm 16 ページ 2001年6月29日 金曜日 午前10時33分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст