Acura CSX. Manual — part 427
02
03
Rear door
20-30
Doors
F
8 x 1.25 mm
29 N·m
(3.0 kgf·m, 22 lbf·ft)
E
8 x 1.25 mm
29 N·m
(3.0 kgf·m, 22 lbf·ft)
A
A
B
C
E
8 x 1.25 mm
29 N·m (3.0 kgf·m, 22 lbf·ft)
F
8 x 1.25 mm
29 N·m
(3.0 kgf·m, 22 lbf·ft)
A
A
A
3. If necessary, replace the door mounting bolts with
the adjusting bolts (P/N 90102-SFA-305) made
specifically for door adjustment, then adjust at the
door: Loosen the door mounting bolts (F) slightly,
and move the door up or down as necessary to
equalize the gaps, and move it in or out until it’s
flush with the body.
4. Check that the door and body edges are parallel. If
necessary, adjust the door cushions (A) to make the
rear of the doors flush with the body.
5. Apply touch-up paint to the hinge mounting bolts,
and around the hinges.
6. Check for water leaks (see step 9 on page 20-29).
08/08/21 15:00:02 61SNR030_200_0032
01
SNR9A00J16126721701MBAT00
20-31
Front and Rear Door Striker Adjustment
B
8 x 1.25 mm
18 N·m (1.8 kgf·m, 13 lbf·ft)
A
C
Make sure the door latches securely without slamming
it. If necessary, adjust the striker (A): The striker nuts
are fixed, but the striker can be adjusted slightly up or
down, and in or out.
1. Loosen the screws (B).
2. Wrap the striker with a shop towel, then adjust the
striker by tapping it with a plastic hammer (C). Do
not tap the striker too hard.
3. Lightly tighten the screws.
4. Hold the outer handle out, and push the door
against the body to be sure the striker allows a
flush fit. If the door latches properly, tighten the
screws to the specified torque, and recheck.
08/08/21 15:00:02 61SNR030_200_0033
*01
*02
SNR9A00J34300000000DAAT00
20-32
Mirrors
Component Location Index
MIRROR HOLDER
POWER MIRROR
REARVIEW MIRROR
Replacement, page 20-34
Replacement,
page 20-33
Replacement, page 20-35
08/08/21 15:00:03 61SNR030_200_0034
01
02
03
SNR9A00J34300044051KBAT10
20-33
Power Mirror Replacement
B
A
Fastener Locations
: Nut, 3
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
A
B
C
1. Raise the door glass fully.
2. Remove these items:
• Door panel (see page 20-7)
• Plastic cover, as needed (see step 4 on page 20-9)
3. Disconnect the connector (A), and detach the
harness clip (B).
4. Remove the maintenance cap (A), and remove the
nuts.
5. While holding the mirror (A), detach the clip (B),
then remove the mirror, and pull the harness (C)
out through the hole in the door. Take care not to
scratch the door.
6. Install the mirror in the reverse order of removal,
and make sure the connector is plugged in properly.
08/08/21 15:00:04 61SNR030_200_0035
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст