Acura CSX. Manual — part 328
*05
*06
08
*07
Outboard Joint Side
Stop ring specifications
Model
Overall Diameter
(A)
Wire Diameter
(B)
16-16
Driveline/Axle
B
C
A
A
B
B
A
B
A
20. Install a new low profile band (A) onto the boot (B),
then hook the tab (C) of the band.
21. Close the hook portion of the band using
commercially available boot band pincers (A), then
hook the tabs (B) of the band.
22. Install the boot band on the other end of the boot,
and repeat steps 20 through 21.
1. Wrap the splines with vinyl tape (A) to prevent
damaging the outboard boot.
2. Install new ear clamp bands (B) and the outboard
boot, then remove the vinyl tape. Be careful not to
damage the outboard boot.
3. Make sure to check the size of a new stop ring.
To avoid driveshaft and vehicle damage,
make sure you install a new stop ring.
6-speed M/T
model
30.5 mm (1.20 in.) 1.8 mm (0.07 in.)
Except
6-speed M/T
model
24.3 mm (0.96 in.) 1.6 mm (0.06 in.)
Replace.
Replace.
08/08/21 14:51:28 61SNR030_160_0016
09
16
13
16-17
B
A
C
B
A
4. Install the stop ring (A) into the driveshaft
groove (B).
5. Pack about 35 g (1.2 oz) grease included in the new
outboard boot set into the driveshaft hole in the
outboard joint.
NOTE: If you are installing a new outboard joint,
the grease is already installed.
6. Insert the driveshaft (A) into the outboard joint (B)
until the stop ring (C) is close to the joint.
Replace.
Use the grease included
in the outboard boot set.
Push.
Push.
08/08/21 14:51:29 61SNR030_160_0017
19
*08
21
10
−
−
−
−
Total grease quantity
Outboard joint:
K20Z2 engine model:
120
140 g
(4.2
4.9 oz)
K20Z3 engine model:
110
130 g
(3.8
4.5 oz)
16-18
Driveline/Axle
10 cm
(4 in.)
A
B
A
A
B
C
A
A
7. To completely seat the outboard joint, pick up the
driveshaft and joint, and tap or hit the assembly
onto a hard surface from a height of about 10 cm
(4 in.).
NOTE: Do not use a hammer as excessive force
may damage the driveshaft. Be careful not to
damage the threaded section (A) of the outboard
joint.
8. Check the alignment of the paint mark (A) you
made with the outboard joint end (B).
To avoid driveshaft and vehicle damage, the
shaft must be all the way into the outboard
joint to ensure the stop ring is properly
seated.
9. Pack the outboard joint (A) with the remaining
grease included in the new outboard boot set.
10. Fit the boot ends (A) onto the driveshaft (B) and
outboard joint (C). Bleed any excess air from the
boot by inserting a flat-tipped screwdriver between
the boot and the joint.
Use the grease included
in the outboard boot set.
08/08/21 14:51:29 61SNR030_160_0018
−
−
−
−
−
−
−
−
*09
*10
24
17
Left driveshaft
Right Driveshaft
Model
Left/Right
Driveshaft
Specified Length (A)
16-19
A
A
B
A
6.0 mm
(0.24 in.) MAX.
3.0 mm (0.12 in.) MAX.
11. Inspect the length (A) of the driveshaft to the figure
as shown, then adjust the boots to halfway
between full compression and full extension.
K20Z2
engine
model
Left
505.5
510.0 mm
(19.88
20.08 in.)
Right
493.0
498.0 mm
(19.41
19.61 in.)
K20Z3
engine
model
Left
511.0
516.0 mm
(20.12
20.31 in.)
Right
486.8
491.8 mm
(19.17
19.36 in.)
12. Close the ear portion (A) of the band using
commercially available boot band pliers
(Kent-Moore J-35910 or equivalent) (B).
13. Check the clearance between the closed ear portion
of the band. If the clearance is not within the
standard, close the ear portion of the band tighter.
14. Repeat steps 12 and 13 for the band on the other
end of the boot.
08/08/21 14:51:30 61SNR030_160_0019
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст