Acura CSX. Manual — part 329
−
01
02
*01
*02
SNR9A00E16226600000KCAT00
−
−
−
−
Grease quantity
K20Z2 engine model:
0.5
1.0 g (0.02
0.04 oz)
K20Z3 engine model:
2.0
3.0 g (0.08
0.12 oz)
16-20
Driveline/Axle
Driveshaft Installation
(P/N 08734-0001)
A
A
B
A
B
A
(P/N 08798-9002)
NOTE: Before starting installation, make sure the
mating surfaces of the joint and the splined section are
clean.
1. Apply about 5 g (0.18 oz) moly 60 paste
(P/N 08734-0001) to the contact area (A) of the
outboard joint and the front wheel bearing.
NOTE: The paste helps to prevent noise and
vibration.
2. Install a new set ring (A) onto the set ring groove
(B) of the driveshaft (left driveshaft).
3. Install a new set ring (A) onto the set ring groove
(B) of the intermediate shaft.
4. Apply super high temp urea grease
(P/N 08798-9002) to the whole splined surface (A) of
the right driveshaft. After applying grease, remove
the grease from the splined grooves at intervals of
2
3 splines and from the set ring groove (B) so
that air can bleed from the intermediate shaft.
Replace.
08/08/21 14:51:31 61SNR030_160_0020
03
*03
04
16-21
E
D
A
E
D
A
C
B
B
A
E
12 x 1.25 mm
59 N·m
(6.0 kgf·m,
43 lbf·ft)
C
12 x 1.25 mm
59 N·m
(6.0 kgf·m,
43 lbf·ft)
D
12 x 1.25 mm
59 N·m
(6.0 kgf·m,
43 lbf·ft)
A
B
5. Clean the areas where the driveshaft contacts the
differential thoroughly with solvent or brake
cleaner, and dry with compressed air.
NOTE: Do not wash the rubber parts with solvent.
6. Insert the inboard end (A) of the driveshaft into the
differential (B) or the intermediate shaft (C) until the
set ring (D) locks in the groove (E).
NOTE: Insert the driveshaft horizontally to prevent
damaging the oil seal.
7. Install the outboard joint (A) into the front hub (B).
8. Connect the knuckle (A) onto the lower arm (B).
During installation, install a new flange bolt and
new self-locking nuts. After lightly tightening all
three fasteners, tighten them to the specified
torque in the following order: the nut on the front
(C), the nut on the rear (D), then the bolt (E).
Replace.
Replace.
Replace.
08/08/21 14:51:44 61SNR030_160_0021
*04
16-22
Driveline/Axle
B
A
K20Z2 engine model:
22 x 1.5 mm
181 N·m
(18.5 kgf·m, 134 lbf·ft)
K20Z3 engine model:
24 x 1.5 mm
245 N·m
(25.0 kgf·m, 180 lbf·ft)
9. Apply small amount of engine oil to the seating
surface of new spindle nut (A).
10. Install the spindle nut, then tighten it. After
tightening, use a drift to stake the spindle nut
shoulder (B) against the driveshaft.
11. Clean the mating surfaces of the brake disc and the
wheel, then install the front wheels.
12. Turn the front wheel by hand, and make sure there
is no interference between the driveshaft and
surrounding parts.
13. Refill the transmission with the recommended
transmission fluid:
• 5-speed manual transmission (see page 13-5)
• 6-speed manual transmission (see page 13-82)
• Automatic transmission (see page 14-232)
14. Lower the vehicle on the lift.
15. Check the wheel alignment, and adjust it if
necessary (see page 18-5).
16. Test-drive the vehicle.
Replace.
Replace.
08/08/21 14:51:45 61SNR030_160_0022
01
02
03
SNR9A00E16236500000KAAT00
16-23
Intermediate Shaft Removal
A
B
A
B
1. Drain the transmission fluid. Reinstall the drain
plug with a new sealing washer:
• 5-speed manual transmission (see page 13-5)
• 6-speed manual transmission (see page 13-82)
• Automatic transmission (see page 14-232)
2. Remove the right driveshaft (see page 16-4).
3. Remove the three flange bolts, then remove the
heat shield.
4. Remove the flange bolt (A) and the two shoulder
bolts (B).
5. Remove the intermediate shaft (A) from the
differential. Hold the intermediate shaft horizontally
until it is clear of the differential to prevent
damaging the oil seal (B).
08/08/21 14:51:45 61SNR030_160_0023
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст