Acura CSX. Manual — part 330
*01
02
*02
01
SNR9A00E16236500000LCAT00
Special Tools Required
16-24
Driveline/Axle
Intermediate Shaft Disassembly
B
A
B
PRESS
A
B
E
C
07JAF-SH20400
D
07965-SD90100
B
A
PRESS
A
B
07965-SD90100
C
07947-SB00100
07JAF-SH20400
• Support base attachment 07JAF-SH20400
• Oil seal driver, 44.5 mm 07947-SB00100
• Support base 07965-SD90100
1. Remove the outer seal (A) and the external snap
ring (B).
2. Press the intermediate shaft (A) out of the
intermediate shaft bearing (B) using the support
base attachment (C), the support base (D), and a
press. Be careful not to damage the bearing
support rings (E) on the intermediate shaft during
disassembly.
3. Remove the internal snap ring (A) from the bearing
support (B).
4. Press the intermediate shaft bearing (A) out of the
bearing support (B) using the half shaft base, the
support base attachment, the 44.5 mm oil seal
driver (C), and a press.
08/08/21 14:51:46 61SNR030_160_0024
01
SNR9A00E16236500000LDAT00
Exploded View
16-25
Intermediate Shaft Reassembly
INTERMEDIATE SHAFT RING
BEARING SUPPORT RING
FLANGE BOLT
10 x 1.25 mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
INTERMEDIATE SHAFT
INTERNAL SNAP RING
EXTERNAL SNAP RING
OUTER SEAL
SET RING
SHOULDER BOLTS
10 x 1.25 mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
INTERMEDIATE
SHAFT BEARING
(P/N 08798-9002)
Replace.
Replace.
Replace.
Pack the interior
of the outer seal.
08/08/21 14:51:46 61SNR030_160_0025
*01
*02
04
03
Special Tools Required
16-26
Driveline/Axle
PRESS
B
D
07749-0010000
C
07746-0010400
A
A
B
PRESS
C
07746-0030400
A
B
A
B
• Support base attachment 07JAF-SH20400
• Driver handle, 15 x 135L 07749-0010000
• Bearing driver attachment, 52 x 55 mm 07746-0010400
• Inner bearing driver attachment, 35 mm
07746-0030400
• Oil seal driver, 64 mm 07GAD-PH70201
• Support base 07965-SD90100
NOTE: Refer to the Exploded View, as needed, during
this procedure.
1. Clean the disassembled parts with solvent, and dry
them with compressed air.
NOTE: Do not wash the rubber parts with solvent.
2. Press a new intermediate shaft bearing (A) into the
bearing support (B) using the 52 x 55 mm bearing
driver attachment (C), the 15 x 135L driver handle
(D), and a press.
3. Install the internal snap ring (A) into the groove of
the bearing support (B).
4. Press the intermediate shaft (A) into the shaft
bearing (B) using the 35 mm inner bearing driver
attachment (C) and a press.
5. Install the external snap ring (A) into the groove of
the intermediate shaft (B).
Replace.
08/08/21 14:51:47 61SNR030_160_0026
*03
*01
02
SNR9A00E16236500000KCAT00
16-27
16-27
Intermediate Shaft Installation
PRESS
B
C
07GAD-PH70201
A
07JAF-SH20400
07965-SD90100
A
B
A
B
6. Install a new outer seal (A) flush with the bearing
support (B) using the support base attachment, the
support base, the 64 mm oil seal driver (C), and a
press.
1. Install a new set ring (A) onto the set ring groove
(B) of the intermediate shaft.
2. Clean the areas where the intermediate shaft
contacts the differential thoroughly with solvent or
brake cleaner, and dry with compressed air.
NOTE: Do not wash the rubber parts with solvent.
3. Insert the intermediate shaft (A) into the differential
until the set ring locks in the groove.
NOTE: Insert the intermediate shaft carefully to
prevent damaging the oil seal (B).
Pack the interior
of the outer seal.
Replace.
Replace.
08/08/21 14:51:48 61SNR030_160_0027
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст