Acura RSX Honda Integra. Manual — part 387
01
S6M6A00J46166453902KDAT00
20-85
Rear Seat Removal/Installation
CARGO
FLOOR MAT
BUSHING
LEFT SEAT-BACK
SEAT BELT BUCKLE
CLIPS
HOOKS
SEAT CUSHION
RIGHT SEAT-BACK
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
B
B
C
LEFT
PIVOT
BRACKET
Fastener Locations
: Bolt, 1
A
: Bolt, 6
B
: Bolt, 1
C
CENTER
PIVOT BRACKET
RIGHT PIVOT BRACKET
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
B
B
B
8 x 1.25 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
NOTE: Take care not to scratch the body or tear the seat covers.
1. Remove the rear seat as shown.
2. Install the seat in the reverse order of removal, and note these items:
• Before attaching the seat cushion, make sure there are no twists or kinks in the seat belt buckle straps.
• When installing the seat cushion, slip the seat belt buckles through the holes in the seat cushion.
• Make sure the seat-back locks securely.
Pull back.
05/06/27 18:24:25 61S6M040_200_0086
01
S6M6A00J46166453995KBAT01
02
01
S6M6A00J46166454031KBAT00
20-86
20-86
Seats
Rear Seat-back Pivot Bracket
Replacement
Rear Seat-back Striker Replacement
A
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
B
D
E
C
Fastener Locations
: Bolt, 2
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A
B
A
1. Remove the rear seat-back (see page 20-85).
2. Remove the pivot bolt (A), then remove the seat-
back pivot bracket (B). If necessary, remove the
toothed lock washer (C), then separate the pivot
bolt, washer (D), bracket, and bushing (E).
3. Install the pivot bracket in the reverse order of
removal, and note these items:
• Apply multipurpose grease to the pivot portion of
the washer and bushing.
• Apply liquid thread lock to the pivot bolt before
reinstallation.
NOTE: Take care not to scratch the interior trim.
1. Remove the rear side trim panel (see page 20-51).
2. Remove the bolts, then remove the seat-back
striker (A).
3. Install the striker in the reverse order of removal,
and move the striker (A) up or down until it is
centered in the seat-back latch (B).
05/06/27 18:24:26 61S6M040_200_0087
01
S6M6A00J46166453971KBAT01
01
S6M6A00J46166453951KBAT02
20-87
20-87
Rear Seat-back Latch Replacement
Rear Seat-back Cover Replacement
Fastener Locations
: Bolt, 2
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
Fastener Locations
: Screw, 1
A
: Clip, 2
B
B
B
C
A
NOTE:
• Take care not to tear the seams or damage the seat
covers.
• Put on gloves to protect your hands.
1. Remove the seat-back (see page 20-85).
2. Remove the latch cover, and pull back the seat-back
cover (see page 20-87).
3. Remove the latch knob.
4. Remove the bolts, then remove the seat-back latch
(A) from the seat-back frame (B).
5. Install the latch in the reverse order of removal, and
make sure the seat-back locks and unlocks properly.
NOTE:
• Take care not to tear the seams or damage the seat
covers.
• Put on gloves to protect your hands.
1. Remove the seat-back (see page 20-85).
2. Remove the screw (A) and clips (B), then remove
the latch cover (C).
(cont’d)
05/06/27 18:24:26 61S6M040_200_0088
02
03
04
20-88
Seats
Rear Seat-back Cover Replacement (cont’d)
A
B
A
B
B
C
A
3. Release the fasteners (A) and hook (B).
4. Pull back the seat-back cover (A), and remove the
clips (B).
5. Pull back the seat-back cover (A) all the way around.
Remove the latch knob (B), and remove the latch
collar (C) by pinching the end and pulling it out.
6. Remove the seat-back cover.
7. Install the cover in the reverse order of removal,
and note these items:
• To prevent wrinkles when installing a seat-back
cover, make sure the material is stretched evenly
over the pad before securing the hook and clips.
• Replace any clips you removed with new ones.
Install them with commercially available
upholstery ring pliers.
05/06/27 18:24:27 61S6M040_200_0089
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст