Honda Odyssey 2004. Manual — part 565
−
−
−
−
01
01
S0X4AZBK791000R114XFAAT20
’03-04 Models
DTC 11-1x (11-10 to 11-19, 11-1A to 11-1F):
DTC 11-4x (11-40 to 11-49, 11-4A to 11-4F):
Special Tools Required
YES
NO
YES
NO
23-202
SRS
DTC Troubleshooting (cont’d)
A
07XAZ-SZ30100
07SAZ-TB4011A
A
Open or Increased Resistance in Driver’s
Airbag First Inflator
Open or Increased Resistance in Driver’s
Airbag Second Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel (A).
5. Connect the special tool (2
connectors) to the
cable reel 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Open or increased resistance in the driver’s
airbag first or second inflator; replace the driver’s
airbag (see page 23-368).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect SRS unit connector A (28P) from the
SRS unit. Do not disconnect the special tool from
the cable reel 4P connector.
11. Disconnect the SRS inflator simulator from SRS
simulator lead F.
Does the SRS indicator stay on?
Is DT C 11-1x or 11-4x indicated?
03/07/29 10:37:44 61S0X050_230_0202
−
−
−
−
*02
*01
*03
YES
NO
YES
NO
23-203
CABLE
REEL 4P CONNECTOR
07XAZ-SZ30100
A
C851
SRS FLOOR HARNESS 28P CONNECTOR C851
GRN/YEL
GRN/WHT
GRN
GRN/
BLK
12. Check resistance between the terminals of SRS
simulator lead F. There should be 1
or less.
Faulty SRS unit or poor contact at SRS unit
connector A (28P) and the SRS unit. Check the
connection between the connector and the SRS
unit. If the connection is OK, replace the SRS unit
(see page 23-382).
Go to step 13.
13. Disconnect the SRS floor harness 28P connector (A)
from SRS main harness 28P connector C851.
14. Check resistance between the No. 9 and No. 10
terminals of the SRS floor harness 28P connector
C851, and between the No. 3 and No. 4 terminals.
There should be 1
or less.
Go to step 15.
Open or increased resistance in the SRS floor
harness; replace the SRS floor harness.
15. Disconnect the cable reel 4P connector from the
SRS main harness.
16. Connect the SRS inflator simulator to SRS
simulator lead F.
(cont’d)
Terminal side of male terminals
Is the r esistance as specif led?
Is the r esistance as specif ied?
03/07/29 10:37:45 61S0X050_230_0203
−
−
−
−
−
05
01
S0X4AZBK791000R113XFAAT00
YES
NO
Special Tools Required
YES
NO
’03-04 Models
DTC 11-3x (11-30 to 11-39, 11-3A to 11-3F):
DTC 11-6x (11-60 to 11-69, 11-6A to 11-6F):
23-204
23-204
SRS
DTC Troubleshooting (cont’d)
CABLE REEL 4P CONNECTOR
A
07XAZ-SZ30100
07SAZ-TB4011A
17. Check resistance between the No. 4 and No. 3
terminals of the cable reel 4P connector, and
between the No. 2 and No. 1 terminals. There
should be 2.0
3.0
.
Open or increased resistance in the SRS
main harness; replace the SRS main harness.
Replace the cable reel (see page 23-377).
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
• SRS short canceler 070AZ-SAA0100
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel (A).
5. Connect the special tool (2
connectors) to the
cable reel 4P connector.
Short to Another Wire or Decreased
Resistance in Driver’s Airbag First Inflator
Short to Another Wire or Decreased
Resistance in Driver’s Airbag Second Inflator
Wire side of female terminals
Is the r esistance as specif ied?
Does the SRS indicator stay on?
03/07/29 10:37:46 61S0X050_230_0204
−
−
−
−
−
−
06
*01
*02
YES
NO
YES
NO
YES
NO
23-205
CABLE
REEL 4P CONNECTOR
07XAZ-SZ30100
C851
A
SRS MAIN HARNESS 28P CONNECTOR C851
GRN/YEL
GRN/WHT
GRN
GRN/
BLK
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Short in the driver’s airbag first or second
inflator; replace the driver’s airbag (see page 23-
368).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the cable reel 4P connector from the
SRS main harness.
11. Disconnect the SRS inflator simulator from SRS
simulator lead F.
12. Check resistance between the terminals of SRS
simulator lead F. There should be an open circuit,
or at least 1 M
.
Go to step 13.
Replace the cable reel (see page 23-377).
13. Disconnect SRS floor harness 28P connector (A)
from the SRS main harness connector C851.
14. Check resistance between the No. 9 and No. 10
terminals of SRS main harness 28P connector C851,
and between the No. 3 and No. 4 terminals. There
should be an open circuit, or at least 1 M
.
Go to step 15.
Short in the SRS main harness; replace the
SRS main harness.
(cont’d)
Wire side of female terminal
Is DT C 11-3x or 11-6x indicated?
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:37:46 61S0X050_230_0205
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст