Mitsubishi Eclipse. Manual — part 122
CRANKSHAFT REAR OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-37
>>B<< DRIVE PLATE <A/T>/FLYWHEEL <M/T>/ADAPTER
PLATE/PLATE <M/T> INSTALLATION
Use special tool MD998781 to hold the flywheel or drive plate
in the same manner as removal. Then install the bolts.
ACX00296AB
MD998781
CYLINDER HEAD GASKET
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-38
CYLINDER HEAD GASKET
REMOVAL AND INSTALLATION
M1112004000365
Pre-removal and Post-installation Operation
• Engine Coolant Draining and Refilling [Refer to GROUP 00, Maintenance Service − Engine Coolant (Change)
• Timing Belt Removal and Installation (Refer to
.)
• Generator Removal and Installation (Refer to GROUP 16, Generator
• Intake Manifold Removal and Installation (Refer to GROUP 15, Intake Manifold
• Exhaust Manifold Removal and Installation (Refer to GROUP 15, Exhaust Manifold
.)
• Water Inlet Pipe Removal and Installation (Refer to GROUP 14, Water Hose and Water Pipe
AC004838
AC
14 ± 1 N·m
117 ± 13 in-lb
3.4 ± 0.5 N·m
31 ± 4 in-lb
3.4 ± 0.5 N·m
31 ± 4 in-lb
<COLD ENGINE>
108 ± 5 N·m
→ 0 N·m
→ 108 ± 5 N·m
80 ± 3 ft-lb
→ 0 in-lb
→ 80 ± 3 ft-lb
1
2
2
3
4
6
4
6
7
9
9
10
N
<COLD ENGINE>
108 ± 5 N·m
→ 0 N·m
→ 108 ± 5 N·m
80 ± 3 ft-lb
→ 0 in-lb
→ 80 ± 3 ft-lb
5
8
REMOVAL STEPS
1.
BREATHER HOSE
2.
BLOW-BY HOSE
3.
PCV HOSE
4.
SPARK PLUG CABLE
5.
BATTERY CABLE
CONNECTION
6.
ROCKER COVER
7.
TIMING BELT REAR COVER
8.
BATTERY CABLE AND
HARNESS BRACKET
<<A>>
>>B<<
9.
CYLINDER HEAD ASSEMBLY
>>A<<
10. CYLINDER HEAD GASKET
REMOVAL STEPS (Continued)
CYLINDER HEAD GASKET
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-39
Required Special Tool:
• MD998051: Cylinder Head Bolt Wrench
REMOVAL SERVICE POINT
.
<<A>> CYLINDER HEAD ASSEMBLY REMOVAL
Using special tool MD998051, loosen the cylinder head bolts in
two or three steps in the order of the numbers shown in the
illustration, then remove the cylinder head assembly.
INSTALLATION SERVICE POINTS
.
>>A<< CYLINDER HEAD GASKET INSTALLATION
1. Wipe off all oil and grease from the gasket mounting
surface.
2. Match the shapes of the cylinder head holes with their
respective cylinder head gasket holes.
.
>>B<< CYLINDER HEAD ASSEMBLY INSTALLATION
CAUTION
Be careful that no foreign material gets into the cylinder,
coolant passages or oil passages. Engine damage may
result.
1. Use a scraper to clean the gasket surface of the cylinder
head assembly.
AC001732
7
3
6
2
5
4
8
1
5
1
8
4
7
6
2
3
EXHAUST SIDE
EXHAUST SIDE
INTAKE SIDE
FRONT OF
ENGINE
MD998051
AB
CYLINDER HEAD GASKET
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-40
CAUTION
Attach the cylinder head bolt washer in the direction
shown in the illustration.
2. Using special tool MD998051 and a torque wrench, tighten
the bolts to the specified torque in the order shown in the
illustration. (in two or three steps)
Tightening torque: 108
± 5 N⋅m (80 ± 3 ft-lb)
3. Loosen the mounting bolts in the reverse sequence to that
shown.
4. Tighten the mounting bolts progressively in the shown
sequence to the specified torque again.
Tightening torque: 108
± 5 N⋅m (80 ± 3 ft-lb)
AC001733
2
3
7
6
1
5
4
8
1
4
8
5
2
3
7
6
EXHAUST SIDE
EXHAUST SIDE
INTAKE SIDE
FRONT OF
ENGINE
AB
MD998051
CYLINDER
HEAD BOLT
WASHER
CYLINDER HEAD BOLT
ROUNDED
SHOULDER
CYLINDER
HEAD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст