Mitsubishi Galant 9G. Manual — part 583
SPECIAL TOOLS
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-4
MD998162
Plug wrench
MD998162-01
Removal and installation of
front case cap plug
MD998783
Plug wrench retainer
General service tool
MD998371
Silent shaft bearing
puller
MD998371-01
Removal of counterbalance
shaft front bearing
MD998372
Silent shaft bearing
puller
MD998372-01
Removal of counterbalance
shaft rear bearing
MB991603
Bearing installer stopper
General service tool
Removal and installation of rear
bearing
MD998705
Silent shaft bearing
installer
MD998373-01 Use
with MB990938-01
Installation of counterbalance
shaft bearing
MD998285
Crankshaft front oil seal
guide
MD998285-01
Installation of crankshaft front
oil seal
MD998375
Crankshaft front oil seal
installer
MD998375-01
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
D998285
SPECIAL TOOLS
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-5
MD998780
Piston pin setting tool
MIT216941
Removal and installation of
piston pin
MB990938
Handle
MB990938-01
Installation of crankshaft rear oil
seal
MD998776
Crankshaft rear oil seal
installer
MD998376-01
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
D998776
GENERATOR AND IGNITION SYSTEM
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-6
GENERATOR AND IGNITION SYSTEM
REMOVAL AND INSTALLATION
M1113001000518
Required Special Tools:
• MB991398: Spark Plug Wrench
• MD998781: Flywheel Stopper
AK303211AB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
10 ± 1 N·m
89 ± 8 in-lb
14 ± 1 N·m
124 ± 8 in-lb
25 ± 4 N·m
19 ±2 ft-lb
13 ± 1 N·m
115 ± 8 in-lb
44 ± 10 N·m
33 ± 6 ft-lb
25 ± 5 N·m
19 ± 2 ft-lb
8.5 ± 0.5 N·m
75 ± 4 in-lb
22 ± 4 N·m
17 ± 2 ft-lb
22 ± 4 N·m
17 ± 2 ft-lb
49 ± 9 N·m
36 ± 6 ft-lb
79 ± 5 N·m
58 ± 3 ft-lb
44 ± 10 N·m
33 ± 6 ft-lb
10 ± 1 N·m
89 ± 8 in-lb
10 ± 1 N·m
89 ± 8 in-lb
8.8 ± 1.0 N·m
78 ± 8 in-lb
REMOVAL STEPS
1. OIL DIPSTICK
2. OIL DIPSTICK GUIDE
3. O-RING
4. AUTO TENSIONER
5. CRANKSHAFT PULLEY
6. WATER PUMP PULLEY
7. IDLER PULLEY
8. CONNECTOR BRACKET
9. GENERATOR
10. IGNITION COIL
11. SPARK PLUG
12. CONNECTOR BRACKET
13. CAMSHAFT POSITION SENSOR
14. O-RING
>>B<<
15. CAMSHAFT POSITION SENSOR
SUPPORT
16. CAMSHAFT POSITION SENSING
CYLINDER
REMOVAL STEPS (Continued)
GENERATOR AND IGNITION SYSTEM
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-7
REMOVAL SERVICE POINT
.
<<A>> SPARK PLUG REMOVAL
Using special tool MB991398, remove the spark plug.
.
<<B>> CAMSHAFT POSITION SENSING
CYLINDER REMOVAL
1. Using special tool MD998781, hold the drive plate.
2. Remove the camshaft position sensing cylinder.
INSTALLATION SERVICE POINT
.
>>A<< CAMSHAFT POSITION SENSING CYLIN-
DER INSTALLATION
1. Using special tool MD998781, hold the drive plate.
2. Tighten the camshaft position sensing cylinder to the
specified torque.
Tightening torque: 22
± 4 N⋅m (17 ± 2 ft-lb)
.
AK300130AC
MB991398
AK300135
MD998781
AC
AK300135
MD998781
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст