Mitsubishi L200. Manual — part 486
42-4
KEYLESS ENTRY SYSTEM TIMER LOCK FUNCTION
INSPECTION . . . . . . . . . . . . . . . . . . . . . . .
METHOD OF REGISTERING A SECRET CODE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRANSMITTER. . . . . . . . . . . . . . . . . . . . . .
TRANSMITTER DISASSEMBLY AND REASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRANSMITTER BATTERY INSPECTION .
SUNROOF ASSEMBLY. . . . . . . . . . .
SERVICE SPECIFICATION(S) . . . . . . . . . .
LUBRICANT(S) . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING . . . . . . . . . . . . . . . .
DIAGNOSIS TROUBLESHOOTING FLOW
SYMPTOM CHART. . . . . . . . . . . . . . . . . . .
SYMPTOM PROCEDURES . . . . . . . . . . . .
SUNROOF DOES NOT OPERATE . . . . . .
ANY OF THE SUNROOF SWITCH POSITION IS
DEFECTIVE . . . . . . . . . . . . . . . . . . . . . . . .
SUNROOF ANTI-TRAP FUNCTION DOES NOT
WORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE . . . . . . . . . . . . . . .
WATER TEST . . . . . . . . . . . . . . . . . . . . . . .
SUNROOF FIT ADJUSTMENT. . . . . . . . . .
SUNROOF OPERATION CHECK . . . . . . .
SUNROOF SAFETY FUNCTION CHECK .
ROOF LID GLASS OPERATION CURRENT CHECK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SUNROOF INITIALIZED ADJUSTMENT . .
SUNROOF ASSEMBLY . . . . . . . . . . . . . . .
SUNROOF ASSEMBLY REMOVAL AND
INSTALLATION. . . . . . . . . . . . . . . . . . . . . .
SUNROOF CHECK. . . . . . . . . . . . . . . . . . .
SUNROOF ASSEMBLY DISASSEMBLY AND
REASSEMBLY . . . . . . . . . . . . . . . . . . . . . .
BODY MOUNTING . . . . . . . . . . . . . . .
BODY MOUNTING REMOVAL AND INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR GATE . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATION(S) . . . . . . . . . .
ON-VEHICLE SERVICE . . . . . . . . . . . . . . .
REAR GATE PANEL FIT ADJUSTMENT . .
REAR GATE OUTSIDE HANDLE ADJUSTMENT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR GATE . . . . . . . . . . . . . . . . . . . . . . . .
REAR GATE REMOVAL AND INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR GATE LATCH ASSEMBLY. . . . . . . .
REAR GATE LATCH ASSEMBLY REMOVAL AND
INSTALLATION . . . . . . . . . . . . . . . . . . . . . .
REAR BODY ROPE HOOK . . . . . . . .
REAR BODY ROPE HOOK REMOVAL AND
INSTALLATION <SINGLE CAB> . . . . . . . .
REAR SIDE PANEL . . . . . . . . . . . . . .
REAR SIDE PANEL REMOVAL AND INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOOSE PANEL. . . . . . . . . . . . . . . . . .
LOOSE PANEL REMOVAL AND INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CUSTOMISATION FUNCTION. . . . . .
HOOD
BODY
42-5
HOOD
ON-VEHICLE SERVICE
ADJUSTMENT OF CLEARANCE AROUND
HOOD
M1421007200301
1. Remove the front deck garnish (Refer to GROUP
51, Windshield Wiper ).
AC501247
2. Loosen the hood hinge mounting bolt and nut but
do not remove them. Move the hood front/rear
and left/right to align the hood level and adjust the
clearance between the hood and body.
3. After the adjustment, tighten the hood hinge
mounting bolt and nut.
4. Install the front deck garnish (Refer to GROUP 51,
Windshield Wiper ).
ADJUSTMENT OF ALIGNMENT OF HOOD
STEPPED PORTION AND HOOD
STRIKER
M1421007300665
1. Remove the radiator grille (Refer to GROUP 51,
Radiator Grille ).
AC501246AB
Hood latch
2. Loosen the hood latch mounting bolts but do not
remove them. Then move the hood latch up/down
and left/right to align the hood level and adjust the
hood striker engagement.
3. After the adjustment, tighten the hood latch
mounting bolts.
4. Install the radiator grille (Refer to GROUP 51,
Radiator Grille ).
ADJUSTMENT OF HOOD HEIGHT
M1421007400349
AC501248
AC502498
AC502955
15.3 mm
AB
A
A
Section A – A
Damper
Turn the damper to the shown dimension to adjust
the hood height. If the hood height is still not even,
turn the damper again until the height is even. The
damper height is altered by roughly 3 mm when the
damper is rotated once.
NOTE: If a rattling noise is heard due to the vibration
of the hood when the vehicle is being driven, adjust
the damper height until the damper is seated on the
hood.
HOOD
BODY
42-6
HOOD
REMOVAL AND INSTALLATION
M1421001602192
Post-installation Operation
• Adjustment of Clearance Around Hood (Refer to
.)
• Adjustment of Alignment of Hood Stepped Portion and
Hood Striker (Refer to
• Adjustment of Hood Height (Refer to
.)
ACA00263
5
1
1
1
1
1
2
3
4
5
6
7
8
9
9
10
11
12
AC
22 ± 4 N·m
22 ± 4 N·m
13 ± 2 N·m
9.0 ± 2.0 N·m
AC804238
AC501251
AC402179
AC402180
A
A
B
B
B
B
7
7
10
7
10
10
AF
NOTE
: Clip positions
Clip
Section A – A
Section B – B
Damper removal
1. Damper
Hood latch and hood lock release
cable removal steps
•
Radiator grille (Refer to GROUP 51,
Radiator Grille .)
2. Hood latch
3. Hood latch cover <Some models>
4. Hood lock release cable protector
5. Hood lock release handle
•
Front splash shield (Refer to
6. Hood lock release cable
Hood removal steps
7. Hood insulator
8. Hood weatherstrip
9. Hood weatherstrip front
•
Windshield washer hose and
windshield washer nozzle (Refer to
GROUP 51, Windshield Washer .)
10. Hood
11. Hood support rod
•
Front deck garnish (Refer to GROUP
51, Windshield Wiper .)
12. Hood hinge
FENDER
BODY
42-7
FENDER
SPECIAL TOOL
M1421000600461
Tool
Number
Name
Use
MB990784
MB990784
Ornament remover
Side turn-signal lamp removal
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст