Mitsubishi L200. Manual — part 361
LOW REVERSE ANNULUS GEAR
AUTOMATIC TRANSMISSION OVERHAUL <V5A5>
23D-59
LOW REVERSE ANNULUS GEAR
DISASSEMBLY AND REASSEMBLY
M1233027100202
AK602049
4
5
6
1
2
3
7
8
9
10
AC
Apply automatic
transmission fluid
to all moving parts
before installation.
Disassembly steps
1.
Snap ring
2.
Overdrive planetary carrier
>>D<<
3.
Thrust bearing No.5
4.
Underdrive sun gear
>>C<<
5.
Thrust bearing No.6
6.
Output planetary carrier
>>B<<
7.
Stopper plate
>>A<<
8.
One-way clutch
9.
Snap ring
10. Low/reverse annulus gear
REASSEMBLY SERVICE POINTS
>>A<< ONE-WAY CLUTCH INSTALLATION
AK602050 AC
Install the one-way clutch so that the arrow stamp is
oriented as shown in the illustration.
>>B<< STOPPER PLATE INSTALLATION
AK602051AC
Claw
Stopper
plate
Groove
Install the stopper plate onto the low/reverse annulus
gear. Make sure that the stopper plate claws are
securely engaged in the annulus gear groove.
CENTRE SUPPORT
AUTOMATIC TRANSMISSION OVERHAUL <V5A5>
23D-60
>>C<< THRUST BEARING No.6 INSTALLATION
CAUTION
Take care not to mistake the thrust bearing No.6
mounting direction.
AK602052AC
Output planetary
carrier side
Apply vaseline or petrolatum jelly on the thrust bear-
ing No.6, and then install on the output planetary car-
rier.
>>D<< THRUST BEARING No.5 INSTALLATION
CAUTION
Take care not to mistake the thrust bearing No.5
mounting direction.
AK602053AC
Overdrive planetary
carrier side
Apply vaseline or petrolatum jelly on the thrust bear-
ing No.5, and then install on the overdrive planetary
carrier.
CENTRE SUPPORT
DISASSEMBLY AND REASSEMBLY
M1233010000162
AK602054
4
5
6
1
2
3
7
8
9
10
AC
Apply automatic
transmission fluid
to all moving parts
before installation.
Disassembly steps
<<A>>
>>C<<
1.
Snap ring
2.
Plate
3.
One-way clutch inner race
>>B<<
4.
O-ring
Disassembly steps (Continued)
CENTRE SUPPORT
AUTOMATIC TRANSMISSION OVERHAUL <V5A5>
23D-61
DISASSEMBLY SERVICE POINT
<<A>> SNAP RING REMOVAL
AK602055AC
MD998924
MB991630
Snap ring
1. Set the special tools as shown in the illustration so
that they are pressed against the inner race of the
one-way clutch.
• Spring compressor (MB991630)
• Spring compressor retainer (MD998924)
2. Screw in the special tool nut, and lightly press
against the inner race of the one-way clutch.
3. Remove the snap ring.
REASSEMBLY SERVICE POINTS
>>A<< D-RING INSTALLATION
1. Apply ATF to the D-ring.
2. Install the D-ring in the groove on the outer and
inner periphery of the piston. Make sure that the
D-ring is not twisted or damaged when installing.
>>B<< O-RING INSTALLATION
AK602056 AC
O-ring
Install the O-ring onto the center support at the posi-
tion shown in the illustration.
>>C<< SNAP RING INSTALLATION
AK602055AC
MD998924
MB991630
Snap ring
1. Set the special tools as shown in the illustration.
• Spring compressor (MB991630)
• Spring compressor retainer (MD998924)
2. Screw in the special tool nut, and lightly press
against the inner race of the one-way clutch.
3. Install the snap ring.
5.
Spring retainer
6.
Return spring
7.
Low/reverse brake piston
>>A<<
8.
D-ring
>>A<<
9.
D-ring
10. Center support
Disassembly steps (Continued)
UNDERDRIVE CLUTCH
AUTOMATIC TRANSMISSION OVERHAUL <V5A5>
23D-62
UNDERDRIVE CLUTCH
DISASSEMBLY AND REASSEMBLY
M1233027300314
AK700896
4
5
6
1
2
3
7
8
9
11
12
13
10
4
5
6
1
2
3
7
8
9
11
12
13
10
AB
Apply automatic
transmission fluid
to all moving parts
before installation.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст