Mitsubishi Lancer (4A9 engine). Manual — part 12
PRECAUTIONS BEFORE SERVICE
GENERAL
00-45
ENGINE KEY CODE AND CHASSIS
NUMBER (CHASSIS NO.) REGISTRA-
TION STEPS FOR THE ENGINE-ECU
CAUTION
• Check that diagnosis code No.P0603 "EEP-
ROM fail" is not set. When diagnosis code No.
P0603 "EEPROM fail" is set, the engine-ECU
cannot store engine key code and chassis No.
even if the engine key code and chassis No.
are registered. If this diagnosis code is set,
troubleshoot the engine-ECU and repair, and
then register the engine key code and chassis
No. to the engine-ECU.
•
AC608435
MB991827
MB991824
MB991910
AB
Diagnosis connector
<LH drive vehicles>
AC700191
MB991827
MB991824
AB
Diagnosis connector
<RH drive vehicles>
MB991910
Before connecting or disconnecting the
M.U.T.-III, turn the ignition switch to the
"LOCK" (OFF) position.
Connect the M.U.T.-III to the 16-pin diagnosis con-
nector as follows.
NOTE: For details on how to use the M.U.T.-III, refer
to the "M.U.T.-III User's Manual."
1. Ensure that the ignition switch is at the "LOCK"
(OFF) position.
2. Start up the personal computer.
3. Connect special tool USB cable (MB991827) to
special tool V.C.I. (MB991824) and the personal
computer.
PRECAUTIONS BEFORE SERVICE
GENERAL
00-46
4. Connect special tool M.U.T.-III main wiring
harness A (MB991910) to the V.C.I.
5. Connect M.U.T.-III main wiring harness A to the
diagnosis connector of the vehicle.
6. Turn the V.C.I. power switch to the "ON" position.
NOTE: When the V.C.I. is energised, the V.C.I.
indicator lamp will be illuminated in a green col-
our.
7. Start the M.U.T.-III system on the personal
computer and turn the ignition switch to the "ON"
position.
NOTE: Since the M.U.T.-III screen display
changes according to the vehicle specifications,
the illustrations for each item may differ from the
actual screen display.
System Select
Select Model Year and System
System List
Model Year
Vehicle Information
Loading Option Setup
OPC
With Option
Option Name
Immobi & Keyless
KOS & Immobi
VF1
Model Name
Model Year
Model Code
Up to 2005 MY
From to 2006 MY
1
2
3
4
5
6
7
8
9
10
MPI/GDI/Diesel
IMMOBI/KOS/Keyless
AT/CVT/A-MT
ABS/ASC/ASTC
SAS
Multi Select 4WD
SRS Airbag
A/C
ETACS
Meter
AC700171
OK button
AB
8. Select "IMMOBI/KOS/Keyless" button from the
"System Select" screen. Then, select the
applicable option code item and push the OK
button.
• The display of "Special Function" screen
changes, depending on the contents of the
option. For vehicles with KOS, select
"KOS&Immobi." For vehicles with WCM, select
"Immobi&Keyless."
9. Select "Special Function" on the next screen.
AC801056
Option: When KOS & Immobi is selected
AB
AC801055
Option: When Immobi & Keyless is selected
AB
10.Select "Key Code Registration" from the "Special
Function" screen.
AC509803
AB
OK button
11.Push the OK button after "Key Code Registration
to Engine ECU" is displayed.
12.Push the OK button after "Completed. Press the
OK button and move to VIN writing function." is
displayed.
AC700604
*****************
*****************
AB
13.Enter the VIN of registering vehicle and push the
OK button.
PRECAUTIONS BEFORE SERVICE
GENERAL
00-47
14.Push the OK button after "VIN Writing will start.
Are you sure?" is displayed.
15.Return to the previous screen and "In Progress" is
displayed at the lower-left corner on the screen.
16.Push the OK button after "Completed." is
displayed.
AC700605
*****************
*****************
AC
17.VIN writing result is displayed.
18.Complete the M.U.T.-III.
19.Disconnecting the M.U.T.-III is the reverse of the
connecting sequence, making sure that the
ignition switch is at the "LOCK" (OFF).
20.Push the OK button after "Completed." is
displayed.
21.Terminate the M.U.T.-III.
22.Turn the ignition switch to the LOCK (OFF)
position and then disconnect the M.U.T.-III.
PRECAUTIONS BEFORE SERVICE
GENERAL
00-48
CHASSIS NO. WRITING STEPS FOR WCM
AND KOS-ECU
CAUTION
• Before the chassis No. registration to WCM,
check that the chassis Nos. of engine-ECU
and vehicle are matched.
• Check that diagnosis code No. B2416 "ECU
internal error" is not set. When diagnosis
code No. B2416 "ECU internal error" is set,
the WCM and the KOS-ECU cannot store the
Chassis No. even if the Chassis No. is written.
If this diagnosis code is set, troubleshoot the
WCM or the KOS-ECU and repair, and then
write the Chassis No. to the WCM or the KOS-
ECU.
•
AC608435
MB991827
MB991824
MB991910
AB
Diagnosis connector
<LH drive vehicles>
AC700191
MB991827
MB991824
AB
Diagnosis connector
<RH drive vehicles>
MB991910
Before connecting or disconnecting the
M.U.T.-III, turn the ignition switch to the
"LOCK" (OFF) position.
Connect the M.U.T.-III to the 16-pin diagnosis con-
nector as follows.
NOTE: For details on how to use the M.U.T.-III, refer
to the "M.U.T.-III operation manual."
1. Ensure that the ignition switch is at the "LOCK"
(OFF) position.
2. Start up the personal computer.
3. Connect special tool M.U.T. -III USB cable
(MB991827) to special tool V.C.I. (MB991824)
and the personal computer.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст