Mitsubishi Outlander XL. Manual — part 1027
ZC3060380000
4.5
2.5
0.5
-
60
-
45
-
30
-
15
0
15
30
45
60
Operation angle of sensor (degree)
50 degrees
(-) angle
(+) angle
45.8 degrees
Voltage (V)
Base point line
of sensor
(0 degree point)
4.
Check that voltages show the values described in the graph
according to the sensor operation angle.
REAR HEIGHT SENSOR CHECK
ZC3052200000
Harness
side
Sensor side
MB991658
1.
Disconnect the sensor connector and connect the special tool
test harness (MB991658) as shown.
2.
Turn the ignition switch to the ON position.
3.
Measure the voltage of sensor connector terminal No. 2.
LIGHTING
54Ac-181
HEADLIGHT AUTOMATIC LEVELING SYSTEM
ZC3060390000
4.5
2.5
0.5
-
60
-
45
-
30
-
15
0
15
30
45
60
42.8 degrees
(-) angle
(+) angle
60 degrees
Voltage (V)
Operation angle of sensor (degree)
Base point line
of sensor
(0 degree point)
4.
Check that voltages show the values described in the graph
according to the sensor operation angle.
REAR COMBINATION LIGHT
REMOVAL AND INSTALLATION
M15410900056USA0000010000
ZC600965AA00
5
1.2 ± 0.7 N·m
11 ± 6 in-lb
4.5 ± 1.5 N·m
40 ± 3 in-lb
4
2
9
6
3
1
12
11
10
8
7
Removal Steps
1.
Rear combination light assembly
2.
Rear combination light unit
Removal Steps
3.
Socket
4.
Bulb
54Ac-182
LIGHTING
REAR COMBINATION LIGHT
Removal Steps
5.
Grommet
6.
Liftgate cover garnish (Refer to
GROUP 52A - Liftgate Trim P.52A-14)
7.
Taillight assembly
8.
Gasket
Removal Steps
9.
Taillight unit
10. Socket
11. Bulb
12. Gasket
REAR SIDE-MARKAER LIGHT
REMOVAL AND INSTALLATION
M15410900176USA0000010000
ZC602020AA00
A
A
Section A – A
Claw
Claw
2
1
1.5 ± 0.2 N·m
14 ± 1 in-lb
3
2
Removal Steps
1.
Rear corner bumper (Refer to GROUP
51A, Rear Bumper Assembly P.
51A-6.)
1.
Rear side-marker light unit
Removal Steps
2.
Socket assembly
3.
Bulb
FOG LIGHT
ON-VEHICLE SERVICE
FOG LIGHT AIMING
M15410900043USA0000010000
PRE-AIMING INSTRUCTIONS
1.
Inspect for rusted or faulty front fog light assemblies.
2.
These conditions must be corrected before a satisfactory
adjustment can be made.
3.
Inspect tire inflation, and adjust if necessary.
4.
If the fuel tank is not full, place a weight in the trunk of the
vehicle to simulate weight of a full tank [3 kg (6.5 pounds) per
gallon].
LIGHTING
54Ac-183
REAR SIDE-MARKAER LIGHT
5.
There should be no other load in the vehicle other than driver
or substituted weight of approximately 68 kg (150 pounds)
placed in driver's position.
6.
Thoroughly clean the front fog light lenses.
7.
Place the vehicle on a level floor, perpendicular to a flat screen
7.62 meters (25.0 ft) away from the bulb center-marks on the
fog light lens.
8.
Rock the vehicle sideways to allow the vehicle to assume its
normal position.
9.
Bounce the front suspension through three (3) oscillations by
applying the body weight to the hood or bumper.
ZC603102
Fog light center
0000
10.
Measure the center of the front fog lights as shown in the
illustration.
ZC603104
Screen
7.62 m (25.0 ft)
0000
(1)
(2)
(3)
(3)
Fog light center
Vehicle center line
11.
Four lines of adhesive tape (or equivalent markings) are
required on screen or wall:
(1)
Position a vertical tape or mark so that it is aligned with
the vehicle center line.
(2)
Measure the distance from the center of the front fog light
lens to the floor. Transfer the measurement to the screen.
Horizontal tape or mark on the screen is for reference of
vertical adjustment.
(3)
Measure the distance from the center line of the vehicle
to the center of each front fog light. Transfer the
measurement to the screen. Vertical tape or mark on the
screen is for reference to the center line of each front fog
light.
FOG LIGHT ADJUSTMENT
ZC603070
Cutoff line
(H)
(V)
Hot zone
mm (in)
53.2 (2.09)
99.8 (3.93)
153.0
(6.02)
599.7 (23.6) 599.7 (23.6)
0001
1.
Check if the beam shining onto the screen is at the standard
value.
Standard value:
(Cutoff line direction): The horizontal line 153.0 mm
(6.02 inches) (1.15 degrees angle) below the
horizontal line (H)
Limit:
(Vertical direction): Area from 53.2 mm (2.09 inches)
(0.4 degrees angle) above the cutoff line to 99.8 mm
(3.93 inches) (0.75 degrees angle) below the cutoff
line
(Horizontal direction): Vertical line (V) ± 599.7 mm (±
23.6 inches) (± 4.5 degrees angle)
54Ac-184
LIGHTING
FOG LIGHT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст