Mitsubishi Outlander GS45X. Manual — part 55
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-217
LIGHTING CONTROL SENSOR REMOVAL AND INSTALLATION
M1540108500223
AC709252
Optical coupler
AB
1
2
3
Note
: Claw positions
A
A
Section A - A
Section B - B
Section C - C
Section D - D
Optical coupler
3
D
C
B
D
C
1
1
1
Claw
Claw
Lighting control
sensor bracket
Lighting control
sensor bracket
Lighting control
sensor bracket
Lighting control
sensor bracket
Claw
Claw
Claw
B
Removal Steps
1.
Lighting control sensor cover
2.
Connector
<<
A
>>
>>
A
3.
Lighting control sensor
Removal Steps (Continued)
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-218
REMOVAL SERVICE POINT
.
<<A>> LIGHTING CONTROL SENSOR REMOVAL
While pushing the clamp to the windshield side, pry up the
clamp to disengage the right and left claws using the screw-
driver (
−), and then remove the lighting control sensor.
INSTALLATION SERVICE POINT
.
>>A<< LIGHTING CONTROL SENSOR INSTALLA-
TION
CAUTION
After executing the lighting control sensor (rain sensor)
adaptation, do not touch the lighting control sensor (or do
not move it from the fixed position).
• Mount the lighting control sensor onto the optical coupler,
and then connect the connector.
• When reusing the lighting control sensor or when the light-
ing control sensor is pushed to check the installation condi-
tion, install the connector and the lighting control sensor
cover and wipe the windshield thoroughly. When the wind-
shield is dry, execute the lighting control sensor (rain sen-
sor) adaptation. <Refer to GROUP 51
− Lighting Control
Sensor (Rain Sensor) Adaptation
NOTE: Be careful not to touch the lighting control sensor
receiver. (The lighting control sensor receiver has limited resis-
tance to oil.)
AC700066
Screwdriver (-)
AG
Claw
Lighting
control
sensor
Clamp
Push
Push
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-219
INSPECTION
HEADLIGHT RELAY CHECK
M1540104000196
HEADLIGHT RELAY (LOW) CHECK <VEHICLES
WITH DISCHARGE HEADLIGHT>
HEADLIGHT RELAY (HIGH) CHECK
Battery voltage
Terminal
number
Normal
conditions
Not energized
3
− 4
No
continuity
With current supply
[terminal 2 (+), terminal 1
(
−)]
Continuity
exists (2
ohms or
less)
AC702996
2
3
4
1
AC
Headlight relay (LOW)
Headlight relay
(LOW)
A-28X
Battery voltage
Terminal
number
Normal
conditions
Not energized
3
− 4
No
continuity
With current supply
[terminal 2 (+), terminal 1
(
−)]
Continuity
exists (2
ohms or
less)
AC702996
2
3
4
1
AB
Headlight relay (HIGH)
Headlight relay
(HIGH)
A-20X
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-220
DAYTIME RUNNING LIGHT RELAY CHECK
<VEHICLES WITH DISCHARGE HEADLIGHT>
M1540113400017
HEADLIGHT LEVELING SWITCH CHECK
M1540101300325
LIGHTING CONTROL SENSOR (LIGHT SENSOR)
CHECK
M1540109000180
Using the scan tool MB991958, check the LIN data list as fol-
lows.
1. Under the direct sunlight, turn the ignition switch to the ON
position and the lighting switch to the AUTO position.
2. When the lighting control sensor receiver is covered by
hand, and if the item No. 7009 (RLS Low beam "ON"
request) and the item No. 7011 (RLS Taillight "ON" request)
turn from OFF to ON, it is judged normal.
NOTE:
.
Battery voltage
Terminal
number
Normal
conditions
Not energized
3
− 4
No
continuity
With current supply
[terminal 1 (+), terminal 2
(
−)]
Continuity
exists (2
ohms or
less)
AC803406
1
3
4
2
AB
Daytime running
light relay
A-23X
Daytime running light relay
Measured
terminals
Switch
position
Resistance value
Ω
4
− 6
0
750
1
1,110
2
1,470
3
1,830
4
2,190
5
− 6
0, 1, 2, 3, 4
2,810
AC700633AD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст