Dodge Dakota (ND). Manual — part 1215
INSTALLATION
NOTE: The seat back is part of the cab back trim
panel. (Refer to 23 - BODY/INTERIOR/REAR CAB
BACK PANEL TRIM - INSTALLATION) for the
appropriate installation procedure.
1. Position the rear seat cushion (4) in the vehicle.
2. Install the fasteners (3) attaching the rear seat
cushion hinge to cab back panel (2).
3. Tighten the fasteners to 34 N·m (25 ft. lbs.).
4. Install the cab back trim panel, (Refer to 23 -
BODY/INTERIOR/REAR CAB BACK PANEL TRIM
- INSTALLATION).
23 - 272
SEATS
ND
SEAT-QUAD CAB
REMOVAL
NOTE: The quad cab rear seat is a 60/40 seat.
Each seat is serviceable separately.
1. Fold the seating cushion (7) up.
2. Remove the jack assembly.
3. Remove the fastener (4) securing the center seat
belt (3)(for left seat removal).
4. Remove the fasteners retaining the seat to the cab
floor.
5. Lift the seat assembly (5) off the retaining studs
and the cab back hooks (4).
6. Remove the seat through the rear door.
ND
SEATS
23 - 273
INSTALLATION
1. Position the seat (5) on the cab back hooks (4) and
the floor studs.
2. Ensure the seat back is firmly hooked to the cab
back retainers.
3. Position the center seat belt (3) onto the floor stud
(5) (for left seat installation).
4. Install the floor fasteners.
5.
Tighten the bolts to 52 N·m (38 ft. lbs.).
6.
Tighten the nuts to 41 N·m (30 ft. lbs.).
7. Install the jack assembly.
23 - 274
SEATS
ND
STATIONARY GLASS
TABLE OF CONTENTS
page
page
BACKLITE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
. . . . . . . . . . . . . . . . . . . . . . . . 277
GLASS-BACKLITE SLIDING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
. . . . . . . . . . . . . . . . . . . . . . . . 279
GLASS-REAR DOOR
. . . . . . . . . . . . . . . . . . . . . . . . 280
WINDSHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
. . . . . . . . . . . . . . . . . . . . . . . . 283
BACKLITE
REMOVAL
CAUTION: It is difficult to salvage the backlite dur-
ing the removal operation. The backlite is part of
the structural support for the roof. The urethane
bonding used to secure the glass to the fence is
difficult to cut or clean from any surface. Since the
molding is set in urethane, it is unlikely it would
be salvaged. Before removing the backlite, check
the availability from the parts supplier.
NOTE: The backlite is attached to the window
frame with urethane adhesive. The urethane adhe-
sive is applied cold and seals the surface area
between the window opening and the glass. The
primer adheres the urethane adhesive to the back-
lite.
1. Roll down door glass.
2. Remove headliner (9) (Refer to 23 - BODY/INTE-
RIOR/HEADLINER - REMOVAL).
ND
STATIONARY GLASS
23 - 275
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст