Dodge Viper SRT-10 (ZB). Manual — part 238
(5) Install the screw attaching the rear of the
quarter panel to the trunk pan and tighten to 6 N·m
(55 in. lbs.).
(6) Install the adjustment bracket screw.
(7) Install the lower quarter panel screw in the
front through the hole cut into the door surround
panel and install a standard body plug.
(8) Install the door opening weatherstrip.
(9) Install the three fascia to the quarter panel
nuts and tighten to 6 N·m (55 in lbs.).
(10) Close the door and check the quarter panel for
gap and flush, adjust if necessary. (Refer to 23 -
BODY/BODY
STRUCTURE/GAP AND
FLUSH
-
SPECIFICATIONS)
(11) Install the tail lamp unit. (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING
-
EXTERIOR/TAIL
LAMP UNIT - INSTALLATION)
(12) For the right side quarter panel, connect the
fuel filler tube. (Refer to 14 - FUEL SYSTEM/FUEL
DELIVERY/FUEL TANK FILLER TUBE - INSTAL-
LATION)
(13) Install the rear wheelhouse splash shield.
(Refer to 23 - BODY/EXTERIOR/REAR WHEEL-
HOUSE SPLASH SHIELD - INSTALLATION)
(14) Install the sill panel. (Refer to 23 - BODY/EX-
TERIOR/ROCKER PANEL COVER - INSTALLA-
TION)
Fig. 10 REAR FASCIA TO REAR QUARTER PANEL
1 - FASCIA TO REAR QUARTER PANEL NUT
2 - REAR QUARTER PANEL RETAINER
3 - BODY ASSEMBLY
4 - REAR FASCIA
5 - ROUND SPRING NUT
6 - FASCIA RETAINER
Fig. 11 FORWARD EDGE OF REAR QUARTER
PANEL
1 - FORWARD EDGE OF REAR QUARTER PANEL
2 - REAR CLIP
23 - 44
EXTERIOR
ZB
REAR QUARTER PANEL (Continued)
Fig. 12 REAR QUARTER PANEL MOUNTING BRACKET
1 - REAR QUARTER PANEL MOUNTING BRACKET
2 - FRAME ASSEMBLY
3 - REAR QUARTER PANEL
4 - REAR QUARTER PANEL TO REAR CLIP BRACKET
5 - REAR CLIP
Fig. 13 QUARTER PANEL - FRONT FASTENERS
1 - QUARTER PANEL
2 - ADJUSTMENT BRACKET
3 - DOOR SURROUND CUT LOCATION
4 - DOOR SURROUND PANEL
5 - ADJUSTMENT BRACKET SCREW
Fig. 14 REAR QUARTER PANEL
1 - REAR QUARTER PANEL
2 - REAR CLIP
ZB
EXTERIOR
23 - 45
REAR QUARTER PANEL (Continued)
REAR WHEELHOUSE SPLASH
SHIELD
REMOVAL
(1) Remove the rear wheel. (Refer to 22 - TIRES/
WHEELS - REMOVAL)
(2) Remove the 11 rear shield screws and remove
the rear shield. (Fig. 15)
(3) Remove the five front shield screws and remove
the front shield.
INSTALLATION
(1) Position the front shield onto the vehicle and
install outside screws loosely.
(2) Position the rear shield onto the vehicle.
(3) Loosely install the remaining screws.
(4) Tighten the five screws attaching the two
shields together then tighten the remaining 11
screws.
SILL PANEL
REMOVAL
(1) Remove the three screws and remove the door
hinge cover. (Fig. 16)
(2) Remove the screws attaching the fender grille
to the fender and the sill.
(3) Remove the seven lower sill screws. (Fig. 17)
(4) Remove the three front wheelhouse splash
shield screws.
(5) Remove the rear screw into the frame near the
quarter panel.
(6) Remove the screws into the door surround
panel. (Fig. 18)
(7) Loosen the sill to fender support nuts.
(8) Remove the sill.
Fig. 15 REAR WHEELHOUSE SPLASH SHIELD
1 - REAR SPLASH SHIELD
2 - SPRING NUT
3 - REAR SPLASH SHIELD - FRONT
4 - BODY ASSEMBLY
23 - 46
EXTERIOR
ZB
INSTALLATION
(1) Position the sill onto the vehicle.
(2) Tighten the sill to fender support nuts.
(3) Install the screws into the door surround panel.
(4) Install the rear screw into the frame near the
quarter panel.
(5) Install the three front wheelhouse splash shield
screws.
(6) Install the seven lower sill screws.
(7) Install the fender grille and install the upper
screw attaching the grille to the fender.
(8) Install the lower grille screw at the sill.
(9) Install the door hinge cover and install the
three screws to the fender.
Fig. 16 DOOR HINGE COVER
1 - U-NUTS (3 PER SIDE)
2 - U-NUTS (2 PER SIDE)
3 - SCREW (1 PER SIDE)
4 - FENDER GRILLE
5 - SCREWS (3 PER SIDE)
6 - HINGE COVER
Fig. 17 SILL PANEL BOLTS
1 - SILL PANEL
2 - SPLASH SHIELD
3 - FENDER GRILLE
4 - FRAME ASSEMBLY
ZB
EXTERIOR
23 - 47
SILL PANEL (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст