Infiniti FX35 / FX45. Manual — part 875

PS-42

< SERVICE INFORMATION >

SERVICE DATA AND SPECIFICATIONS (SDS)

Steering Gear

INFOID:0000000001327729

Tie-rod ball joint inner socket

Swinging torque

1.0

−

7.8 N·m (0.11

−

0.79 kg-m, 9

−

69 in-lb)

Measurement on spring balance
• Measuring point: L mark see below,

L=83.2 mm (3.28 in).

12.1

−

93.7 N (1.2

−

9.6 kg, 3.0

−

21 lb)

Axial end play

0.2 mm (0.01 in) or less

Tie-rod length “L”

135.2 mm (5.32 in)

Steering gear type

PR26AM

SGIA0358E

SGIA0167E

Steering gear model

PR26AM

Rack neutral position, dimension “L” (rack stroke)

67.0 mm (2.64 in)

Rack sliding force

At the neutral point:
Range within

±

11.5 mm

(

±

0.453 in) from the neutral

position
(in power ON)

Area average value

147

−

211 N (15

−

21.5 kg, 33

−

47 lb)

Allowable variation

98 N (10 kg, 22 lb) or less

Whole area (in power OFF)

Peak value

294 N (30 kg, 66 lb) or less

Allowable variation

147 N (15 kg, 33 lb) or less

SGIA0629J

SERVICE DATA AND SPECIFICATIONS (SDS)

PS-43

< SERVICE INFORMATION >

C

D

E

F

H

I

J

K

L

M

A

B

PS

N

O

P

Oil Pump

INFOID:0000000001327730

Steering Fluid

INFOID:0000000001327731

Oil pump relief hydraulic pressure

9,900

−

10,700 kPa (101

−

109.1 kg/cm

2

, 1436

−

1552 psi)

Fluid capacity

Approx. 1.0

(1-1/8 US qt, 7/8 Imp qt)

RAX-1

DRIVELINE/AXLE

C

E

F

G

H

I

J

K

L

M

SECTION

RAX

A

B

RAX

N

O

P

CONTENTS

REAR AXLE

SERVICE INFORMATION . . . . . . .

2

PRECAUTIONS . . . . . . . . . . . . ...

2

Caution . . . . . . . . . . . . . . . . . ..

2

PREPARATION . . . . . . . . . . . . ...

3

Special Service Tool . . . . . . . . . . . .....

3

Commercial Service Tool . . . . . . . . . . ..

4

NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .

5

NVH Troubleshooting Chart . . . . . . . . . ..

5

REAR WHEEL HUB AND KNUCKLE . . . ...

6

On-Vehicle Inspection . . . . . . . . . . . ..

6

Removal and Installation . . . . . . . . . . ..

6

Disassembly and Assembly . . . . . . . . . ..

7

REAR DRIVE SHAFT . . . . . . . . . .

10

Removal and Installation . . . . . . . . . . .

10

Disassembly and Assembly . . . . . . . . . .

10

SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .

17

Wheel Bearing . . . . . . . . . . . . . . .

17

Drive Shaft . . . . . . . . . . . . . . . ...

17

RAX-2

< SERVICE INFORMATION >

PRECAUTIONS

SERVICE INFORMATION

PRECAUTIONS

Caution

INFOID:0000000001327522

Observe the following precautions when disassembling and servicing drive shaft.
• Perform work in a location which is as dust-free as possible.
• Before disassembling and servicing, clean the outside of parts.
• Prevention of the entry of foreign objects must be taken into account during disassembly of the service loca-

tion.

• Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean cover

must be placed over parts.

• Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adhering

to parts.

• Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by

blowing with air or wiping with paper shop cloths.