Infiniti FX35 / FX45. Manual — part 874
PS-38
< SERVICE INFORMATION >
HYDRAULIC LINE
VQ35DE AWD MODEL
JSGIA0177GB
1.
Reservoir tank
2.
Reservoir tank bracket
3.
Suction hose
4.
High pressure hose
5.
Power steering oil pump
6.
Steering gear assembly
7.
Oil cooler
8.
Clamp
9.
Eye bolt
10. Copper washer
11.
Eye bolt
12. Copper washer
13. Oil pressure sensor
Refer to
and the followings for the symbols in the figure.
: Apply power steering fluid.
HYDRAULIC LINE
PS-39
< SERVICE INFORMATION >
C
D
E
F
H
I
J
K
L
M
A
B
PS
N
O
P
VK45DE AWD MODEL
Removal and Installation
INFOID:0000000001327724
VQ35DE MODELS
• Refer to
for tightening torque. Install in the reverse order of removal.
NOTE:
Refer to component parts location and do not reuse non-reusable parts.
JSGIA0219GB
1.
Reservoir tank
2.
Suction hose
3.
High pressure hose
4.
Oil cooler
5.
Pressure sensor
6.
Steering gear assembly
7.
Clamp
8.
Eye bolt
9.
Copper washer
10. Reservoir tank bracket
11.
Eye bolt
and the followings for the symbols in the figure.
: Apply power steering fluid.
PS-40
< SERVICE INFORMATION >
HYDRAULIC LINE
• Confirm with mating marking that if it is in phase with hose and
clamp, then correct if needs.
• To install eye joint, join projection of eye joint into notch of power
steering pump, and attach eye joint to power steering pump prop-
erly. Then, tighten eye bolt by hands fully, and tighten it with a
specified torque.
• Connect harness connector into pressure sensor securely.
VK45DE MODELS
• Refer to
for tightening torque. Install in the reverse order of removal.
NOTE:
Refer to component parts location and do not reuse non-reusable parts.
• Confirm with mating marking that if it is in phase with hose and
clamp, then correct if needs.
• To install eye joint, join projection of eye joint into notch of power
steering pump, and attach eye joint to power steering pump prop-
erly. Then, tighten eye bolt by hands fully, and tighten it with a
specified torque.
SGIA0563E
SGIA0533E
SGIA0563E
SGIA0537E
SERVICE DATA AND SPECIFICATIONS (SDS)
PS-41
< SERVICE INFORMATION >
C
D
E
F
H
I
J
K
L
M
A
B
PS
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
Steering Wheel
INFOID:0000000001327725
Steering Angle
INFOID:0000000001327726
Steering Column
INFOID:0000000001327727
Steering Outer Socket and Inner Socket
INFOID:0000000001327728
End play of the axle direction for steering wheel
0 mm (0 in)
Steering wheel play on the outer circumference
0
−
35 mm (0
−
1.38 in)
Inner wheel
Degree minute (Decimal degree)
Minimum
32
°
00
′
(32.0
°
)
Nominal
35
°
00
′
(35.0
°
)
Maximum
36
°
00
′
(36.0
°
)
Outer wheel
Degree minute (Decimal degree)
Nominal
30
°
00
′
(30.0
°
)
Steering column length “ L1 ”
572 mm (22.52 in)
SGIA0556E
Steering gear type
PR26AM
Tie-rod ball joint outer socket
Swinging torque
0.3
−
2.9 N·m (0.03
−
0.29 kg-m, 3
−
25 in-lb)
Measurement on spring balance
• Measuring point: cotter pin hole of stud
4.84
−
46.7 N (0.5
−
4.8 kg, 1.0
−
10 lb)
Rotating torque
0.3
−
2.9 N·m (0.03
−
0.29 kg-m, 3
−
25 in-lb)
Axial end play
0.5 mm (0.02 in) or less
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст