Infiniti FX35 / FX45. Manual — part 876
PREPARATION
RAX-3
< SERVICE INFORMATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
Special Service Tool
INFOID:0000000001327523
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST33251000
( — )
Drift
• Removing wheel hub
• Removing wheel bearing outer side
inner race
• Installing wheel hub
• Inspection of wheel bearing rotating
torque
ST35300000
( — )
Drift
a: 45 mm (1.77 in) dia.
b: 59 mm (2.32 in) dia.
• Installing wheel hub
• Inspection of wheel bearing rotating
torque
KV40100900
( — )
Drift
a: 52 mm (2.05 in) dia.
b: —
Wheel bearing rotating torque inspec-
tion
KV38100500
( — )
Drift
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.
Installing drive shaft plug
KV38102200
( — )
Drift
a: 90 mm (3.54 in) dia.
b: 31 mm (1.22 in) dia.
Installing drive shaft plug
ZZA0982D
ZZA0881D
ZZA0539D
ZZA0701D
ZZA0920D
RAX-4
< SERVICE INFORMATION >
PREPARATION
Commercial Service Tool
INFOID:0000000001327524
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
RAX-5
< SERVICE INFORMATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000001327525
Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
—
—
NVH in PR
section
NVH in RFD
section
NVH in RAX
and RSU
section
Re
fe
r to
REAR AXL
E i
n
t
h
is cha
rt.
NVH in WT
section
NVH in WT
section
Ref
e
r t
o
DRIV
E SHAFT
in
th
is ch
art
.
NVH in BR
section
NVH in PS
section
Possible cause and SUSPECTED PARTS
Ex
ce
ss
iv
e j
oi
nt
an
gl
e
Jo
in
t s
lid
in
g res
ist
an
ce
Imb
al
anc
e
Im
p
rop
er i
n
s
ta
lla
tio
n
,
lo
os
en
es
s
P
a
rt
s interference
PR
OP
EL
LE
R
S
H
A
F
T
DIFFERENTIAL
REA
R
AXLE AND REAR S
U
SPENSION
REA
R
AXLE
TI
RE
ROAD W
H
EEL
DRIV
E SHAFT
BR
AK
E
S
T
EERING
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
REAR AXLE
Noise
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
RAX-6
< SERVICE INFORMATION >
REAR WHEEL HUB AND KNUCKLE
REAR WHEEL HUB AND KNUCKLE
On-Vehicle Inspection
INFOID:0000000001327526
Make sure the mounting conditions (looseness, back lash) of each component and component status (wear,
damage) are normal.
WHEEL BEARING INSPECTION
With the vehicle raised, inspect the following.
• Move wheel hub in the axial direction by hand. Check that there is no looseness of front wheel bearing.
• Rotate wheel hub and make sure there is no unusual noise or other irregular conditions. If there are any
irregular conditions, replace wheel hub and bearing assembly.
Removal and Installation
INFOID:0000000001327527
COMPONENTS
REMOVAL
1.
Remove tires from vehicle with power tool.
2.
Remove cotter pin. Then remove lock nut from drive shaft.
3.
Remove brake caliper with power tool. Hang it in a place where it will not interfere with work. Refer to
25, "Removal and Installation of Brake Caliper Assembly"
.
NOTE:
• Avoid depressing brake pedal while brake caliper is removed.
4.
Remove disc rotor. Refer to
BR-25, "Removal and Installation of Brake Caliper Assembly"
5.
Remove parking cable and parking shoe from back plate. Refer to
PB-4, "Removal and Installation"
6.
Remove wheel sensor from axle. Refer to
.
CAUTION:
Do not pull on wheel sensor harness.
7.
Separate drive shaft from wheel hub and bearing assembly by lightly tapping the end with a suitable ham-
mer and wood block. If it is hard to separate, use a suitable puller.
8.
Remove fixing bolts of wheel hub and bearing assembly with power tool, then remove wheel hub and
bearing assembly from axle.
Axial end play
: 0.05 mm (0.002 in) or less
1.
Drive shaft
2.
Bushing
3.
Axle
4.
Back plate
5.
Anchor block
6.
Wheel bearing
7.
Wheel hub
8.
Cotter pin
SDIA1481E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст