Infiniti G37 Coupe. Manual — part 823
HEADLINING
INT-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
9.
Disconnect antenna feeder connectors (A) of antenna amplifier
and sub-antenna feeder (1) after removing rear pillar finisher
(LH), and then remove antenna feeder securing clip and ground
cable fixing bolt (B).
10. With a removal tool, remove body side mounting plastic clip from rear end of headlining.
11. Pull map lamp assembly toward vehicle lower, and disengage
dual-lock fastener (A) and metal clips (B).
CAUTION:
Map lamp assembly is crimped from back of headlining.
Remove it by disengaging the crimped area of back of map
lamp assembly after removing headlining from the vehicle.
12. Put front seat to front must and recline seat back to backward.
13. Remove headlining, turn and take out from right side door.
CAUTION:
• When removing, 2 workers are required. (1 for the front
and rear of headlining)
• Cover center console finisher upper surface with a shop
cloth to prevent it from being damaged.
• Do not bend headlining when removing.
14. Remove the following parts after removing headlining.
• Map lamp assembly (without LDW system). Refer to
INL-97, "Removal and Installation"
• Roof harness assembly.
• Antenna feeder assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Install headlining assembly after inserting clips to clip holder of headlining rear end.
• Do not bend headlining when installing.
SUNROOF
: Clip
JMJIA0971ZZ
JMJIA0099GB
JMJIA0975ZZ
INT-24
< ON-VEHICLE REPAIR >
HEADLINING
SUNROOF : Exploded View
INFOID:0000000001767475
SUNROOF : Removal and Installation
INFOID:0000000001767474
REMOVAL
1.
Remove front pillar garnish (LH/RH) and body side welt (LH/RH).
Refer to
INT-14, "Removal and Installation"
2.
Remove antenna feeder securing clips with a remover tool after
removing front pillar garnish (LH), then disconnect antenna
feeder connectors (A).
1.
Sun visor holder
2.
Sun visor cover
3.
Sun visor assembly
4.
Roof front finisher
5.
Assist grip
6.
Headlining assembly
7.
Rear hidden clip
8.
Antenna feeder
9.
Over head console
10. Map lamp assembly
11. Dual lock fastener
12. Roof harness
13. Roof bracket
14. Roof plate assembly
15. Map lamp lens
16. Assist grip clip
: Pawl
: Metal clip
JMJIA0970ZZ
: Clip
JMJIA0101GB
HEADLINING
INT-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3.
Remove front roof finisher mounting metal clips and pawls, and
then remove front roof finisher (1).
4.
Remove sun visor assembly (LH/RH).
• Remove sun visor cover.
• Remove sun visor assembly mounting screws.
• Disconnect vanity mirror lamp harness connectors.
5.
Rotate 45 degrees and remove sun visor holder (1) (LH/RH).
6.
Remove mounting plastic clips (A) using a screwdriver (B) of
front and rear assistance grips (1), and then remove assist grips.
7.
Remove rear seat cushion and seatback. Refer to
SE-160, "Removal and Installation"
8.
Remove front kicking plate inner (LH/RH), rear side finisher (LH/RH), rear pillar finisher (LH/RH).
Refer to
INT-14, "Removal and Installation"
9.
Disconnect antenna feeder connectors (A) of antenna amplifier
and sub-antenna feeder (1) after removing rear pillar finisher
(LH), and then remove antenna feeder securing clip and ground
cable fixing bolt (B).
10. With a removal tool, remove body side mounting plastic clip from rear end of headlining.
: Pawl
: Metal clip
JMJIA0097GB
JMJIA0098GB
JMJIA0096GB
: Clip
JMJIA0971ZZ
INT-26
< ON-VEHICLE REPAIR >
HEADLINING
11. Pull map lamp assembly toward vehicle lower, and disengage
dual-lock fastener (A) and metal clips (B).
CAUTION:
Map lamp assembly is crimped from back of headlining.
Remove it by disengaging the crimped area of back of map
lamp assembly after removing headlining from the vehicle.
12. Put front seat to front must and recline seat back to backward.
13. Remove headlining, turn and take out from right side door.
CAUTION:
• When removing, 2 workers are required. (1 for the front
and rear of headlining)
• Cover center console finisher upper surface with a shop
cloth to prevent it from being damaged.
• Do not bend headlining when removing.
14. Remove the following parts after removing headlining.
• Map lamp assembly (without LDW system). Refer to
INL-97, "Removal and Installation"
• Roof harness assembly.
• Antenna feeder assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Install headlining assembly after inserting clips to clip holder of headlining rear end.
• Do not bend headlining when installing.
JMJIA0099GB
JMJIA0972ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст