Infiniti FX35, FX50 (S51). Manual — part 1518
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
PWC-133
< SYMPTOM DIAGNOSIS >
[FRONT & REAR WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
Diagnosis Procedure
INFOID:0000000005248243
1.
REPLACE POWER WINDOW MAIN SWITCH
Replace power window main switch. Refer to
PWC-136, "Removal and Installation"
>> INSPECTION END
PWC-134
< SYMPTOM DIAGNOSIS >
[FRONT & REAR WINDOW ANTI-PINCH]
POWER WINDOW SWITCH DOES NOT ILLUMINATE
POWER WINDOW SWITCH DOES NOT ILLUMINATE
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000005248244
1.
REPLACE POWER WINDOW MAIN SWITCH
Replace power window main switch.
Refer to
PWC-136, "Removal and Installation"
.
>> INSPECTION END
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000005248245
1.
REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Replace front power window switch (passenger side).
Refer to
PWC-137, "Removal and Installation"
.
>> INSPECTION END
REAR LH
REAR LH : Diagnosis Procedure
INFOID:0000000005248246
1.
REPLACE REAR POWER WINDOW SWITCH LH
Replace rear power window switch LH.
Refer to
PWC-138, "Removal and Installation"
.
>> INSPECTION END
REAR RH
REAR RH : Diagnosis Procedure
INFOID:0000000005248247
1.
REPLACE REAR POWER WINDOW SWITCH RH
Replace rear power window switch RH.
Refer to
PWC-138, "Removal and Installation"
.
>> INSPECTION END
PRECAUTIONS
PWC-135
< PRECAUTION >
[FRONT & REAR WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005248248
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
PWC-136
< REMOVAL AND INSTALLATION >
[FRONT & REAR WINDOW ANTI-PINCH]
POWER WINDOW MAIN SWITCH
REMOVAL AND INSTALLATION
POWER WINDOW MAIN SWITCH
Removal and Installation
INFOID:0000000005248249
REMOVAL
1.
Remove the front door finisher.
Refer to
INT-11, "Removal and Installation"
.
2.
Power window main switch (1) is removed from power window
main switch finisher (2) using flat-bladed screw driver (A) etc.
CAUTION:
Never fold pawl of front door finisher.
INSTALLATION
Install in the reverse order of removal.
NOTE:
If power window main switch is replaced or is removed, it is necessary to perform the initialization procedure.
JMKIA2670ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст