Infiniti EX35. Manual — part 551
DLN-154
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
FRONT OIL SEAL
d.
Confirm that the dimension of the side flange installation mea-
surement (A) in the figure comes into the following.
11. Install drive shaft. Refer to
.
12. Install rear wheel sensor. Refer to
13. Install center muffler. Refer to
.
14. Refill gear oil to the final drive and check oil level. Refer to
15. Check the final drive for oil leakage. Refer to
Standard
A
: 326 – 328 mm (12.83 – 12.91 in)
SDIA1039E
SIDE OIL SEAL
DLN-155
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SIDE OIL SEAL
2WD
2WD : Exploded View
INFOID:0000000003135823
1.
Drive pinion lock nut
2.
Companion flange
3.
Front oil seal
4.
Pinion front bearing
5.
Gear carrier
6.
Side oil seal
7.
Side flange
8.
Collapsible spacer
9.
Pinion rear bearing
10. Pinion height adjusting washer
11.
Drive pinion
12. Side bearing adjusting washer
13. Side bearing
14. Side gear thrust washer
15. Circular clip
16. Side gear
17. Lock pin
18. Pinion mate gear
19. Pinion mate thrust washer
20. Pinion mate shaft
21. Drive gear
22. Differential case
23. Bearing cap
24. Filler plug
25. Gasket
26. Rear cover
27. Drain plug
A.
Oil seal lip
B.
Screw hole
C.
For the tightening torque, refer to
.
: Apply gear oil.
: Apply anti-corrosion oil.
: Apply Genuine Silicone RTV or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
: Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products
Refer to
for symbols not described above.
JPDID0129GB
DLN-156
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
SIDE OIL SEAL
2WD : Removal and Installation
INFOID:0000000003135824
REMOVAL
1.
Remove center muffler with a power tool. Refer to
2.
Remove rear wheel sensor. Refer to
BRC-107, "FRONT WHEEL SENSOR : Exploded View"
3.
Remove drive shaft from final drive with a power tool. Then suspend it by wire, etc. Refer to
4.
Install attachment (A) [SST: KV40104100 (
—
)] to side
flange, and then pull out the side flange with the sliding hammer
(B) [SST: ST36230000 (J-25840-A)].
NOTE:
Circular clip installation position: Final drive side
5.
Remove side oil seal, using a flat-bladed screwdriver.
CAUTION:
Never damage gear carrier.
INSTALLATION
1.
Apply multi-purpose grease to side oil seal lips.
2.
Install side oil seal until it becomes flush with the case end,
using the drift [SST: KV38100200 (J-26233)].
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
3.
Install side flange with the following procedure.
a.
Attach the protector [SST: KV38107900 (J-39352)] to side oil
seal.
b.
After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the pro-
tector.
c.
Put a suitable drift on the center of side flange, then drive it until sound changes.
JSDIA0105ZZ
SDIA1584E
SDIA1585E
SDIA0822E
SIDE OIL SEAL
DLN-157
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
NOTE:
When installation is completed, driving sound of the side flange turns into a sound that seems to affect the
whole final drive.
d.
Confirm that the dimension of the side flange (1) installation
measurement (A) in the figure comes into the following.
4.
Install drive shaft. Refer to
5.
Install rear wheel sensor. Refer to
.
6.
Install center muffler. Refer to
.
7.
When oil leaks while removing, check oil level after the installa-
tion. Refer to
.
AWD
AWD : Exploded View
INFOID:0000000003135825
Standard
A
: 326 – 328 mm (12.83 – 12.91 in)
JSDIA0106ZZ
1.
Drive pinion lock nut
2.
Companion flange
3.
Front oil seal
4.
Pinion front bearing
5.
Gear carrier
6.
Side oil seal
7.
Side flange
8.
Collapsible spacer
9.
Pinion rear bearing
10. Pinion height adjusting washer
11.
Drive pinion
12. Side bearing adjusting washer
13. Side bearing
14. Side gear thrust washer
15. Circular clip
16. Side gear
17. Lock pin
18. Pinion mate gear
19. Pinion mate thrust washer
20. Pinion mate shaft
21. Drive gear
22. Differential case
23. Bearing cap
24. Filler plug
JSDIA0027GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст