Infiniti EX35. Manual — part 502
DLK-222
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
FRONT DOOR
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000003556336
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and cloth to protect
door and body.
REMOVAL
1.
Remove mounting bolts of door check link on the vehicle.
2.
Remove front door harness grommet, and then pull out the harness from the vehicle.
3.
Disconnect front door harness connector.
4.
Remove door hinge mounting nuts (door side), and then remove door assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
Refer to
for symbols in the figure.
JMKIA2087GB
FRONT DOOR
DLK-223
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-223, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR ASSEMBLY : Adjustment
INFOID:0000000003556337
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Remove front fender. Refer to
DLK-219, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
8.
Install front fender. Refer to
DLK-219, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000003556338
Portion
Clearance
Surface height
Front fender – Front door
A – A
2.6 – 4.6 (0.102 – 0.181)
- 1.0 – 1.0 (- 0.039 – 0.039)
Front door – Rear door
B – B
2.6 – 4.6 (0.102 – 0.181)
- 1.0 – 1.0 (- 0.039 – 0.039)
JMKIA2049ZZ
DLK-224
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
FRONT DOOR
DOOR STRIKER : Removal and Installation
INFOID:0000000003556339
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000003586657
DOOR HINGE : Removal and Installation
INFOID:0000000003556341
REMOVAL
1.
Remove front fender. Refer to
DLK-219, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-222, "DOOR ASSEMBLY : Removal and Installation"
.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA2049ZZ
FRONT DOOR
DLK-225
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove front door hinge mounting bolts, and then remove front door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-223, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000003586658
DOOR CHECK LINK : Removal and Installation
INFOID:0000000003556343
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "DRIVER SIDE : Removal and Installation"
(driver side) or
INT-14, "PASSENGER SIDE : Removal and Installation"
(passenger side).
2.
Fully close the front door window.
3.
Remove front door speaker. Refer to
AV-158, "Removal and Installation"
(base audio without navigation),
AV-414, "Removal and Installation"
(BOSE audio without navigation), or
AV-905, "Removal and Installa-
(BOSE audio with navigation).
4.
Remove mounting bolts of door check link on the vehicle.
5.
Remove mounting bolts of door check link on door panel.
6.
Take door check link out from the hole of door panel.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
JMKIA2049ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст