Infiniti G35 (V35) Sedan. Manual — part 1392
TM-260
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
REAR OIL SEAL
REAR OIL SEAL
2WD
2WD : Exploded View
INFOID:0000000000957161
2WD : Removal and Installation
INFOID:0000000000957162
REMOVAL
1.
Remove exhaust front tube and center muffler with power tool. Refer to
.
2.
Remove rear propeller shaft. Refer to
.
3.
Remove rear oil seal (1) using a flat-bladed screwdriver (A).
CAUTION:
Be careful not to scratch rear extension assembly.
INSTALLATION
1.
As shown in the figure, use the drift [SST: ST33400001 (J-
26082)] (A) to drive rear oil seal into rear extension assembly
until it is flush.
CAUTION:
• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.
2.
Install rear propeller shaft. Refer to
.
3.
Install exhaust front tube and center muffler. Refer to
2WD : Inspection
INFOID:0000000000957163
INSPECTION AFTER INSTALLATION
After completing installation, check A/T fluid leakage and A/T fluid level. Refer to
.
AWD
AWD : Exploded View
INFOID:0000000000957164
(AWD).
AWD : Removal and Installation
INFOID:0000000000957165
REMOVAL
1.
Remove exhaust front tube and center muffler with power tool. Refer to
.
JPDIA0037ZZ
JPDIA0039ZZ
REAR OIL SEAL
TM-261
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Remove rear propeller shaft. Refer to
.
3.
Remove transfer assembly from A/T assembly. Refer to
4.
Remove rear oil seal (1) using a flat-bladed screwdriver (A).
CAUTION:
Be careful not to scratch adapter case assembly.
INSTALLATION
1.
As shown in the figure, use the drift [64 mm (2.52 in) dia. com-
mercial service tool] (A) to drive rear oil seal into adapter case
assembly until it is flush.
CAUTION:
• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.
2.
Install transfer assembly to A/T assembly. Refer to
3.
Install rear propeller shaft. Refer to
4.
Install exhaust front tube and center muffler. Refer to
AWD : Inspection
INFOID:0000000000957166
INSPECTION AFTER INSTALLATION
After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to
.
JPDIA0038ZZ
JPDIA0040ZZ
TM-262
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
REVOLUTION SENSOR
REVOLUTION SENSOR
2WD
2WD : Exploded View
INFOID:0000000000957167
2WD : Removal and Installation
INFOID:0000000000957168
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Drain ATF through drain plug.
3.
Remove exhaust front tube and center muffler with power tool. Refer to
.
4.
Remove rear propeller shaft. Refer to
5.
Remove control rod. Refer to
.
6.
Remove exhaust mounting bracket. Refer to
1.
Rear extension
2.
A/T
3.
Bracket
4.
Oil pan gasket
5.
Clip
6.
Oil pan mounting bolt
7.
Oil pan
8.
Drain plug
9.
Drain plug gasket
10.
Revolution sensor
11.
Self-sealing bolt
*
: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
Refer to
for symbols not described on the above.
SCIA8271E
REVOLUTION SENSOR
TM-263
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7.
Disconnect heated oxygen sensor 2 harness connectors (A).
8.
Remove heated oxygen sensor 2 harness (B) from clips (1).
9.
Remove bracket (2) from transmission assembly.
10. Remove clips (1).
11. Remove oil pan (2) and oil pan gasket.
12. Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, place wooden blocks to
prevent from damaging control valve with TCM and trans-
mission case.
13. Remove rear engine mounting member with power tool. Refer to
14. Remove engine mounting insulator (rear). Refer to
15. Remove tightening bolts for rear extension assembly and trans-
mission case.
16. Tap rear extension assembly with a soft hammer (A).
: Vehicle front
: Bolt
SCIA8269E
3
: Drain plug
: Vehicle front
: Oil pan mounting bolt
1
: Self-sealing bolt
A
: Bolt
SCIA8117E
JPDIA0026ZZ
JPDIA0027ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст