Infiniti G35 (V35) Sedan. Manual — part 1391
TM-256
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
PARKING COMPONENTS
18. Remove return spring (1) from parking pawl (2).
19. Remove rear oil seal (1) from rear extension using flat-blade
screwdriver (A).
CAUTION:
Be careful not to scratch rear extension.
INSTALLATION
1.
As shown in the figure, use a drift [SST: ST33400001 (J-26082)]
(A) to drive rear oil seal into the rear extension until it is flush.
CAUTION:
• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.
2.
Install return spring (1) to parking pawl (2).
SCIA6180J
JPDIA0033ZZ
JPDIA0035ZZ
SCIA6180J
PARKING COMPONENTS
TM-257
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Install parking pawl (with return spring) (1) and pawl shaft (2) to
rear extension.
4.
Install parking actuator support (1) to rear extension.
5.
Install bearing (1) to rear extension.
CAUTION:
Take care with the direction of needle bearing. Refer to
289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
6.
Install seal rings (1) to output shaft.
7.
Install parking gear (1) to output shaft (2).
JPDIA0032ZZ
JPDIA0031ZZ
SCIA6179J
JPDIA0030ZZ
JPDIA0029ZZ
TM-258
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
PARKING COMPONENTS
8.
Install output shaft (1) in transmission case.
9.
Install bearing race (1) to output shaft (2).
10. Apply recommended sealant (Genuine Anaerobic Liquid Gasket
GI-15, "Recommended Chemical Prod-
.) to rear extension assembly as shown in the
figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.
11. Install rear extension assembly (with needle bearing) to trans-
mission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
JPDIA0028ZZ
JPDIA0057ZZ
A
: Start and finish point shall be in
the center of two bolts.
B
: 3 – 5 mm (0.12 – 0.20 in)
Sealant
width (C)
: 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant
height (C)
: 0.4 – 1.0 mm (0.016 – 0.04 in)
JPDIA0036ZZ
SCIA3431E
PARKING COMPONENTS
TM-259
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
12. Tighten rear extension assembly bolts to the specified torque.
13. Install engine mounting insulator (rear). Refer to
.
14. Install rear engine mounting member. Refer to
.
15. Install control rod. Refer to
16. Install rear propeller shaft. Refer to
.
17. Install exhaust front tube and center muffler. Refer to
18. Install drain plug to oil pan. Tighten a necessary drain plug with specified torque. Refer to
CAUTION:
Do not reuse drain plug gasket.
19. Pour ATF into A/T assembly. Refer to
.
2WD : Inspection
INFOID:0000000000957160
INSPECTION AFTER REMOVAL
If the contact surface on parking actuator support (1), parking pawl
(2) and etc. has excessive wear, abrasion, bend, or any other dam-
age, replace the components.
INSPECTION AFTER INSTALLATION
After completing installation, check the following item.
• A/T fluid leakage and A/T fluid level. Refer to
• A/T position. Refer to
TM-230, "2WD : Inspection and Adjustment"
.
1
: Self-sealing bolt
A
: Bolt
JPDIA0026ZZ
JPDIA0034ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст