Infiniti G35 (V35) Sedan. Manual — part 1393
TM-264
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
REVOLUTION SENSOR
17. Remove rear extension assembly (With needle bearing) from
transmission case.
18. Disconnect revolution sensor connector (A).
CAUTION:
Be careful not to damage connector
19. Disengage terminal clip (
).
20. Remove revolution sensor (1) from transmission case.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
• Do not place in an area affected by magnetism.
INSTALLATION
1.
Install revolution sensor (1) in transmission case. Tighten a nec-
essary bolt for revolution sensor with specified torque.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
• Do not place in an area affected by magnetism.
SCIA3431E
JPDIA0011ZZ
: Bolt
JPDIA0041ZZ
: Bolt
JPDIA0041ZZ
REVOLUTION SENSOR
TM-265
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Connect revolution sensor connector (A).
3.
Engage revolution sensor harness with clip (
).
4.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-15, "Recommended Chemical Prod-
.) to rear extension assembly as shown in the
figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from transmission case and rear extension assembly
mounting surfaces.
5.
Install rear extension assembly (with needle bearing) to trans-
mission case.
CAUTION:
Insert the tip of parking rod between the parking pole and
the parking actuator support when assembling the rear
extension assembly.
6.
Tighten rear extension assembly bolts to the specified torque.
7.
Install rear engine mounting member. Refer to
.
8.
Install oil pan gasket to oil pan.
CAUTION:
• Do not reuse oil pan gasket.
• Install it in the direction to align hole positions.
JPDIA0011ZZ
A
: Start and finish point shall be in the
center of two bolts.
B
: 3 – 5 mm (0.12 – 0.20 in)
Sealant
width (C)
: 1.0 –2.0 mm (0.04 – 0.08 in)
Sealant
height (C)
: 0.4 – 1.0 mm (0.016 – 0.04 in)
JPDIA0036ZZ
SCIA3431E
1
: Self-searing bolt
A
: Bolt
JPDIA0026ZZ
TM-266
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
REVOLUTION SENSOR
• Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
9.
Install oil pan (2) (with oil pan gasket) and clips (1) to transmis-
sion case.
CAUTION:
• Install it so that drain plug (3) comes to the position as
shown in the figure.
• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
10. Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Tighten necessary oil pan mounting bolts with specified torque.
CAUTION:
Do not reuse oil pan mounting bolts.
11. Install drain plug to oil pan. Tighten a necessary drain plug with
specified torque.
CAUTION:
Do not reuse drain plug gasket.
12. Install bracket (2) to transmission assembly.
13. Install heated oxygen sensor 2 harness (B) to clips (1).
14. Connect heated oxygen sensor 2 harness connector (A).
15. Install exhaust mounting bracket. Refer to
.
16. Install control rod. Refer to
17. Install rear propeller shaft. Refer to
.
18. Install exhaust front tube and center muffler. Refer to
19. Pour ATF into A/T assembly. Refer to
.
20. Connect the battery cable to the negative terminal.
2WD : Inspection
INFOID:0000000000957169
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
• If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to
.
INSPECTION AFTER INSTALLATION
After completing installation, check the following item.
: Vehicle front
: Oil pan mounting bolt
SCIA8117E
: Vehicle front
: Vehicle front
: Bolt
JPDIA0021ZZ
SCIA8269E
SCIA5199E
REVOLUTION SENSOR
TM-267
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• A/T fluid leakage and A/T fluid level. Refer to
• A/T position. Refer to
TM-230, "2WD : Inspection and Adjustment"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст