Infiniti G35 (V35). Manual — part 78
ASSEMBLY
AT-303
D
E
F
G
H
I
J
K
L
M
A
B
AT
23. Install needle bearing to transmission case.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
●
Apply petroleum jelly to needle bearing.
24. Install revolution sensor to transmission case, and then tighten
revolution sensor mounting bolt to the specified torque. Refer to
.
CAUTION:
●
Do not subject it to impact by dropping or hitting it.
●
Do not disassemble.
●
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
●
Do not place in an area affected by magnetism.
25. As shown in the figure, use a drift to drive rear oil seal into the
rear extension until it is flush.
CAUTION:
●
Do not reuse rear oil seal.
●
Apply ATF to rear oil seal.
26. Install return spring (1) to parking pawl (2).
27. Install parking pawl (with return spring) and pawl shaft to rear
extension.
SCIA5031E
SCIA2320E
SCIA5311E
SCIA6180J
SCIA3424E
AT-304
ASSEMBLY
28. Install parking actuator support to rear extension.
29. Install needle bearing (1) to rear extension.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
●
Apply petroleum jelly to needle bearing.
Refer to GI section to make sure icons (symbol marks) in the fig-
ure. Refer to
30. Install seal rings to output shaft.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
31. Install parking gear to output shaft.
32. Install output shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)
SCIA3423E
SCIA6179J
SCIA5209E
SCIA5247E
SCIA5030E
ASSEMBLY
AT-305
D
E
F
G
H
I
J
K
L
M
A
B
AT
33. Install bearing race to output shaft.
34. Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-46, "Recommended Chemical Prod-
.) to rear extension assembly as shown in
the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.
35. Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
36. Tighten rear extension assembly mounting bolts to the specified
CAUTION:
Do not reuse self-sealing bolts.
37. Install needle bearing in drum support.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
●
Apply petroleum jelly to needle bearing.
SCIA5245E
SCIA8228E
SCIA5029E
SCIA6941E
SCIA5198E
AT-306
ASSEMBLY
38. Install direct clutch assembly in reverse brake.
CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
39. Install high and low reverse clutch assembly in direct clutch.
40. Using a flat-bladed screwdriver, adjust the drive plate.
41. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
SCIA5019E
SCIA2306E
SCIA3169E
SCIA5018E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст