Volkswagen Golf / Golf GTI / Jetta. Manual — part 143
01-151
Work sequence
- Connect VAG 1551 scan tool (or VAG 1552).
Then switch ignition on and select Motronic
Engine Control Module (ECM) -J220- with the
"Address word" 01. (Connecting scan tool and
selecting Engine Control Module (ECM)
Page
01-12
).
Work step 1: Check DTC memory
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Operate scan tool taking into account the
information on the display:
- Press buttons -0- and -2- for function "Check
DTC memory" and confirm entry with Q button.
X Diagnostic Trouble Codes (DTCs) detected!
The number of Diagnostic Trouble Codes (DTCs)
stored or "No DTC detected!" will be shown on the
display.
If a DTC is stored:
Readiness code
01-152
Repair Diagnostic Trouble Codes
(DTCs) printed out using DTC table:
SAE P0 codes
Page 01-
30
,
SAE P1 codes
Page 01-
58
,
SAE P2 codes
Page 01-
98
,
SAE P3 codes
Page 01-
99
.
If no DTC is stored:
- Press
button.
- Continue with work step 3
Work step 2: Erase DTC memory
Rapid data transfer
HELP
Select function XX
Indicated on display:
Note:
The readiness code is reset or
erased each time DTC memory is
erased.
- Press buttons -0- and -5- for
function "Erase DTC memory"
and confirm entry with -Q- button.
Rapid data transfer
DTC memory is erased!
Indicated on display:
Readiness code
01-153
Note:
If the ignition is switched off between
"Check DTC memory" and "Erase
DTC memory" the DTC memory will
not be erased.
- Press
button.
Work step 3: Adjust the Throttle
Valve Control Module -J338- to the
Motronic Engine Control Module
(ECM) -J220-
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -4- for
function "Initiate basic setting"
and confirm entry with -Q- button.
Basic setting
Input display group number XXX
Indicated on display:
- Press buttons -0-, -6- and -0- for
"Display group number 60" and
confirm entry with -Q- button.
System in basic setting 60
xxx.x %
xxx.x % x
ADP. runs
Indicated on display: (1 to 4
display zones)
- Check specifications in display
zones 3 and 4:
Display zone 3: 0 to 8
Display zone 4: ADP. runs, ADP.
OK.
System in basic setting 60
xxx %
xxx % 8
ADP. OK.
Indicated on display: (1 to 4
display zones)
Readiness code
01-154
- Terminate engine basic setting at earliest after
30 seconds by pressing
button.
If the display does not indicate as described:
- Check Throttle Valve Control Module -J338-
Page 24-59
.
If the display indicates as described:
- Start engine and run at idle.
Note:
Engine must not be switched again off during
work sequence.
Work step 4: Requesting temperature
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -8- for function "Read
measured value (data) block" and confirm entry
with Q button.
Read measured value block
Input display group number XXX
Indicated on display:
- Press buttons -0-, -0- and -4- for "Display group
number 4" and confirm entry with -Q- button.
Read measured value block 4
1
2
3
4
Indicated on display: (1 to 4
display zones)
Readiness code
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст