Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 312
5
Door Windows
⇒ “5.1 Overview - Front Door Window”, page 380
⇒ “5.2 Overview - Rear Door Window”, page 381
⇒ “5.3 Overview - Fixed Rear Door Window”, page 382
⇒ “5.4 Front Door Window, Removing and Installing”, page 382
⇒ “5.5 Rear Door Window, Removing and Installing”, page 387
⇒ “5.6 Fixed Rear Door Window, Removing and Installing”, page
5.1
Overview - Front Door Window
Note
The illustration shows the left side. The right side is identical.
1 - Front Door
2 - Front Door Window
❑ Removing and instal‐
ling. Refer to
3 - Door Inner Cover
❑ Removing and instal‐
ling. Refer to
4 - Bolt
❑ Quantity: 3
❑ Tightening specification
-item 4-
.
5 - Window Regulator Motor
❑ Removing and instal‐
ling. Refer to
6 - Cable Bushing
7 - Hooks
❑ Quantity: 2
❑ For attaching the door
window on the window
regulator
5.2
Overview - Rear Door Window
1 - Rear Door
2 - Window Regulator
❑ Removing and instal‐
ling. Refer to
.
3 - Expanding Pin
❑ Together with the
spreader plug for at‐
taching the door window
4 - Spreader Plug
❑ Together with the ex‐
panding pin for attach‐
ing the door window
5 - Window Regulator Motor
❑ Removing and instal‐
ling. Refer to
.
6 - Door Control Module
7 - Bolt
❑ Quantity: 3
❑ Tightening specification
-item 5-
.
8 - Door Inner Cover
❑ Removing and instal‐
ling. Refer to
.
9 - Door Window
❑ Removing and installing. Refer to
5.3
Overview - Fixed Rear Door Window
1 - Fixed Door Window
❑ Removing and instal‐
ling. Refer to
.
2 - Seal
❑ Part of the window
glass.
3 - Bolt
❑ 6 Nm
❑ Quantity: 2
4 - Cap
❑ Quantity: 2
5 - Rear Door
6 - Clip
❑ Quantity: 2
5.4
Front Door Window, Removing and In‐
stalling
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Note
The following describes the removal and installation of the right door window. The left side is identical.
Removing
– Remove the front door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Front Door Trim Panels; Front Door Trim Panel,
Removing and Installing .
– Remove the door inner cover -3-. Refer to
⇒ “2.6 Door Inner Cover, Removing and Installing”,
.
– Pry out the cable bushing -6-.
– Lower the door window -2- until the hooks -7- in the door win‐
dow are accessible.
Note
♦
If it is not possible to do this step because the window regulator motor is faulty, then remove the window
regulator motor -5-.
♦
Then the door window can be moved to the necessary position.
– Carefully push the hooks -7- through the opening in the win‐
dow glass. While doing so, slightly lift the door window so that
it does not fall back into the hooks.
– Remove the door window -1- upward from the window regu‐
lator.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст