Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 310
– While cutting free, press the cutting wire -3- against the rear
window using the Flush Bonded Window Kit - Wedge (5 pc.) -
VAG1474/5- in order to have clearance on the body flange.
– Then cut the rear window free at the bottom.
– Hold the rear window with two suction lifter when cutting free.
Caution
More force will be needed because at the bottom of the rear
window two adhesive beads will be cut through.
– Remove the rear window at the two suction lifters from the rear
window.
Installing
Install in reverse order of removal. Note the following:
– Prepare the undamaged window for glazing. Refer to
⇒ “1.4 Undamaged Window Glass, Preparing for Installation”,
– Prepare the new window glass for glazing. Refer to
⇒ “1.5 New Window Glass, Preparing for Installation”,
– Prepare the body flange for glazing. Refer to
⇒ “1.6 Body Flange, Preparing for Installation”, page 359
– Installation Instructions. Refer to
⇒ “1.3 Installation Instructions for Bonded Window Glass”,
– Minimum Curing Time. Refer to
⇒ “1.1 Minimum Curing Times for Bonded Windows”,
3.2.2
Damaged Rear Window, Removing
– Protect the body and vehicle interior from glass splinters.
– Remove the glass pieces up to the adhesive.
– Remove the connections for the window defogger and anten‐
na.
– Bond the flange -2- all around with fabric reinforced adhesive
tape.
– Cut through the adhesive (with the remaining glass) in the
window opening with the Window Cutter - VAG1561A- and the
Window Cutter - VAG1561- .
WARNING
Always wear protective eyewear and leather gloves.
4
Side Windows
⇒ “4.1 Overview - Front Side Window”, page 373
⇒ “4.2 Overview - Rear Side Window”, page 374
⇒ “4.3 Front Side Window, Removing and Installing”, page 375
⇒ “4.4 Rear Side Window, Removing and Installing”, page 377
4.1
Overview - Front Side Window
1 - Centering Clip
2 - Clip
❑ Quantity: 2
3 - Side Window
❑ Removing and instal‐
ling. Refer to
.
4 - Seal
❑ Part of the front side
window
5 - PUR Adhesive Sealant
❑ Bead diameter: width =
6.5 mm dimension -a-,
height = 10 mm dimen‐
sion -b- (including resid‐
ual material on window
glass and window glass
flange)
❑ Minimum curing time.
Refer to
4.2
Overview - Rear Side Window
⇒ “4.2.1 Overview - Rear Side Window, Sedan”, page 374
⇒ “4.2.2 Overview - Rear Side Window, Wagon”, page 375
4.2.1
Overview - Rear Side Window, Sedan
1 - Side Window
❑ Side window, removing.
Refer to
2 - Seal
❑ Part of the rear side win‐
dow
3 - PUR Adhesive Sealant
❑ Bead diameter: Height =
10 mm dimension -b-,
width = 6.5 mm dimen‐
sion -a- (including pre-
coating, residual materi‐
al on window glass and
window glass flange)
❑ Minimum curing time.
Refer to
.
4 - Body Flange
5 - Gap Dimension
❑ Must be applied evenly.
4.2.2
Overview - Rear Side Window, Wagon
1 - Side Window
❑ Side window, removing.
Refer to
.
2 - PUR Adhesive Sealant
❑ Bead diameter: Height =
10 mm -dimension b-,
width = 6.5 mm
-dimension a- (including
pre-coating, residual
material on window
glass and window glass
flange)
❑ The width of the glass/
paint primer application
is 14 mm -dimension c-
❑ Minimum curing time
3 - Body Flange
4 - Guide Clip
❑ Quantity: 2
4.3
Front Side Window, Removing and In‐
stalling
⇒ “4.3.1 Front Side Window, Removing and Installing”,
page 375
⇒ “4.3.2 Damaged Front Side Window, Removing”, page 377
4.3.1
Front Side Window, Removing and Installing
WARNING
Always wear protective eyewear and leather gloves.
Note
The Cutting Tool for Bonded Windows - Wire Reel - VAS6452/1- is used to remove the front side window.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст