Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 851
– Mark the position of the eccentric screw -2- in relation to the
subframe, for example using a felt-tip pen.
– Unscrew the nut -1- and remove the bolt -2-.
– Remove lower transverse link.
Installing
Install in reverse order of removal while noting the following:
Tightening Specifications
♦ Refer to
⇒ “5.1 Overview - Transverse Link”, page 181
♦ Refer to
⇒ “2.4 Left/Right Rear Level Control System Sensor G76 /
G77 , Removing and Installing”, page 282
♦ Refer to
⇒ “1.1 Wheel Bolt Tightening Specifications”, page 286
♦ Rear exhaust system. Refer to ⇒ Rep. Gr. 26 ; Exhaust Pipes/
Mufflers; Overview - Muffler .
• Observe the mark made for the eccentric screw -2- in relation
to the subframe.
• Only fasten the transverse link in the curb weight position.
• For vehicles with a level control system sensor, perform the
basic setting for the wheel damping electronics using the Ve‐
hicle Diagnostic Tester.
• For vehicles with a level control system sensor, perform a
headlamp basic setting. Refer to ⇒ Electrical Equipment; Rep.
Gr. 94 ; Headlamp; Headlamp, Adjusting .
– Perform an axle alignment. Refer to
⇒ “3.5 Axle Alignment Procedure”, page 302
5.5
Tie Rod, Removing and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Torque Wrench 1332 40-200Nm - VAG1332-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Bolt - Stabilizer Bar to Subframe
♦ Bolt- Tie Rod to Wheel Bearing Housing
♦ Bolt - Tie Rod to Subframe
♦ Nut - Tie Rod to Subframe
Removing
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheel.
– Remove the bolts -arrows- for the stabilizer bar -1-
– Loosen the nut -1- and the bolt -3- several turns.
– Remove the bolt -3-.
– Remove the nut -1- and then remove the bolt -4- to the rear.
– Remove the tie rod -2-.
Installing
Install in reverse order of removal. Note the following:
Tightening Specifications
♦ Refer to
⇒ “5.2 Overview - Tie Rod”, page 184
♦ Refer to
⇒ “4.1 Overview - Stabilizer Bar”, page 177
♦ Refer to
⇒ “1.1 Wheel Bolt Tightening Specifications”, page 286
• The tie rods may only be fastened when the dimension be‐
tween wheel hub center and lower edge of wheel housing,
measured before assembly, is achieved.
– Perform an axle alignment.
6
Suspension Strut/Shock Absorber,
Spring
⇒ “6.1 Overview - Suspension Strut, Shock Absorber and Spring”,
page 191
⇒ “6.2 Shock Absorber, Removing and Installing”, page 193
⇒ “6.3 Shock Absorber, Servicing”, page 200
⇒ “6.4 Spring, Removing and Installing”, page 202
6.1
Overview - Suspension Strut, Shock Ab‐
sorber and Spring
⇒ “6.1.1 Overview - Suspension Strut, Shock Absorber and
Spring, Torsion Beam Axle”, page 191
⇒ “6.1.2 Overview - Suspension Strut, Shock Absorber and
Spring, Multi-Link Suspension”, page 192
6.1.1
Overview - Suspension Strut, Shock Absorber and Spring, Torsion Beam
Axle
1 - Bolt
❑ 50 Nm + 45°
❑ Replace after removal
2 - Shock Absorber
❑ Removing and instal‐
ling. Refer to
❑ Always vent and drain
faulty shock absorbers
before disposal.
3 - Upper Spring Support
❑ Place on body “tab”.
4 - Spring
❑ Removing and instal‐
ling. Refer to
5 - Clamping Ring
❑ Press in the clamping
ring until flush after in‐
stalling the stone chip
protection.
6 - Low Spring Support
❑ Spring end rotated up to
stop
❑ Insert the pin into the
hole in the spring mount
on the axle beam when
installing.
7 - Axle Beam
8 - Stone Chip Protection
9 - Expanding Rivet
10 - Bolt
❑ 70 Nm + 180°
❑ Replace after removal
❑ Always tighten threaded connection in curb weight position
6.1.2
Overview - Suspension Strut, Shock Absorber and Spring, Multi-Link Sus‐
pension
1 - Bolt
❑ 50 Nm + 45°
❑ Replace after removal
2 - Shock Absorber
❑ Removing and instal‐
ling. Refer to
❑ Observe the installation
position of the cable tie
closure
❑ Always vent and drain
faulty shock absorbers
before disposal.
3 - Upper Spring Support
❑ Place on body “tab”.
4 - Spring
❑ Removing and instal‐
ling. Refer to
5 - Clip
❑ Serves as an assembly
aid
6 - Low Spring Support
❑ Spring end rotated up to
stop
❑ When assembling, in‐
sert the pin into the
spring mount opening
on the lower transverse
link -arrow-.
7 - Lower Transverse Link
8 - Nut
❑ 70 Nm + 180°
❑ Replace after removal
❑ Always tighten threaded connection in curb weight position
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст