Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 852
9 - Bolt
❑ Replace after removal
6.2
Shock Absorber, Removing and Instal‐
ling
⇒ “6.2.1 Shock Absorber, Removing and Installing, Torsion Beam
Axle”, page 193
⇒ “6.2.2 Shock Absorber, Removing and Installing, Multi-Link
Suspension, Left Shock Absorber”, page 195
⇒ “6.2.3 Shock Absorber, Removing and Installing, Multi-Link
Suspension, Right Shock Absorber”, page 197
6.2.1
Shock Absorber, Removing and Instal‐
ling, Torsion Beam Axle
Special tools and workshop equipment required
♦ Torque Wrench 1332 40-200Nm - VAG1332-
♦ Torque Wrench 1410 - VAG1410-
♦ Spring Compressor Kit - Spring Tensioner - VAG1752/1-
♦ Spring Compressor Kit - Spring Retainer with Inserts -
VAG1752/3A-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Bolts - Shock Absorber to Body
♦ Bolts - Shock Absorber to Axle Beam
Removing
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheel.
– Remove the rear wheel housing liner. Refer to ⇒ Body Exte‐
rior; Rep. Gr. 66 ; Wheel Housing Liner; Rear Wheel Housing
Liner, Removing and Installing .
Vehicles with a Vehicle Level Sensor
– Remove the bolt -1-.
– Remove the lever of the Left Rear Level Control System Sen‐
sor - G76- -2- from the axle beam -3-
Vehicles with Adaptive Chassis DCC
– Disconnect the connector -1- from the shock absorber -2-.
– Remove the wire -3- from the shock absorber -2- -arrow-.
Note
If there is moisture in the connector area, blow compressed air on
the contacts on the shock absorber and the connector.
Continuation for All Vehicles
– Insert the Spring Tensioner -1-.
1 - Spring Compressor Kit - Spring Tensioner - VAG1752/1-
2 - Spring Compressor Kit - Spring Retainer with Inserts -
VAG1752/3A-
WARNING
Make sure the coil spring is seated correctly in the Spring
Compressor Kit - Spring Retainer with Inserts - VAG1752/3A-
-2- (danger of accident).
– Tension the coil spring until the shock absorber is not under
tension.
– Remove the bolts -1- from the shock absorber -2-.
– Remove the bolt -1-.
– Remove the shock absorber.
Installing
Installation is the reverse of removal, with special attention to the
following:
– For vehicles with a vehicle level sensor, perform the basic set‐
ting for the wheel damping electronics. Refer to Vehicle Diag‐
nostic Tester .
Tightening Specifications
♦ Refer to
⇒ “6.1.1 Overview - Suspension Strut, Shock Absorber and
Spring, Torsion Beam Axle”, page 191
♦ Refer to
⇒ “1.1 Wheel Bolt Tightening Specifications”, page 286
♦ Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Wheel Housing Liner;
Rear Wheel Housing Liner, Removing and Installing .
6.2.2
Shock Absorber, Removing and Instal‐
ling, Multi-Link Suspension, Left Shock
Absorber
Special tools and workshop equipment required
♦ Torque Wrench 1332 40-200Nm - VAG1332-
♦ Torque Wrench 1410 - VAG1410-
♦ Spring Compressor Kit - Spring Tensioner - VAG1752/1-
♦ Spring Compressor Kit - Spring Retainer with Inserts -
VAG1752/3A-
♦ Spring Compressor Kit - Adapter Blocks - VAG1752/9-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Bolts - Shock Absorber to Body
♦ Bolt - Shock Absorber to Lower Transverse Link
♦ Nut - Shock Absorber to Lower Transverse Link
Removing
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheel.
– Remove the rear wheel housing liner. Refer to ⇒ Body Exte‐
rior; Rep. Gr. 66 ; Wheel Housing Liner; Rear Wheel Housing
Liner, Removing and Installing .
Vehicles with a Vehicle Level Sensor
– Remove the bolts -1-.
– Remove the Left Rear Level Control System Sensor - G76-
-2- bracket.
Vehicles with Adaptive Chassis DCC
– Disconnect the connector -1- from the shock absorber -2-.
– Remove the wire -3- from the shock absorber -2- -arrow-.
Note
If there is moisture in the connector area, blow compressed air on
the contacts on the shock absorber and the connector.
Continuation for All Vehicles
– Insert the Spring Compressor -3-.
1 - Spring Compressor Kit - Spring Retainer with Inserts -
VAG1752/3A-
2 - Spring Compressor Kit - Adapter Blocks - VAG1752/9-
3 - Spring Compressor Kit - Spring Tensioner - VAG1752/1-
WARNING
Make sure the coil spring is seated correctly in the Spring
Compressor Kit - Spring Retainer with Inserts - VAG1752/3A-
-2- (danger of accident).
– Tension the coil spring until the shock absorber is not under
tension.
– Remove the bolts -1- from the shock absorber -2-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст