Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 223
55 – Hood, Lids
1
Hood
⇒ “1.1 Overview - Hood”, page 24
⇒ “1.2 Overview - Release Cable”, page 26
⇒ “1.3 Hood, Removing and Installing”, page 26
⇒ “1.4 Hood, Adjusting”, page 28
⇒ “1.5 Latch, Removing and Installing”, page 31
⇒ “1.6 Latch, Adjusting”, page 33
⇒ “1.7 Hood Release Lever, Removing and Installing”,
page 35
⇒ “1.8 Catch, Removing and Installing”, page 36
⇒ “1.9 Catch, Adjusting”, page 38
⇒ “1.10 Hinges, Removing and Installing”, page 39
⇒ “1.11 Insulation, Removing and Installing”, page 41
⇒ “1.12 Gas-Filled Strut, Removing and Installing”, page 44
⇒ “1.13 Gas-Filled Strut, Venting”, page 45
⇒ “1.14 Release Cable, Removing and Installing”, page 45
1.1
Overview - Hood
1 - Hood
❑ Removing and instal‐
ling. Refer to
.
❑ Adjusting. Refer to
.
2 - Adjusting Buffer
❑ Quantity: 2
3 - Insulation
❑ Removing and instal‐
ling. Refer to
.
4 - Center Seal
5 - Catch
❑ Removing and instal‐
ling. Refer to
.
6 - Bolt
❑ 12 Nm
❑ Quantity: 2
7 - Side Seal
❑ Right and left
8 - Hinge
❑ Removing and instal‐
ling. Refer to
9 - Nut
❑ 22 Nm
❑ Quantity: 2 on each side
10 - Bolt
❑ 22 Nm
❑ Quantity: 2 on each side
11 - Protective Film
❑ For the adjusting buffer
12 - Latch
❑ Removing and installing. Refer to
⇒ “1.5 Latch, Removing and Installing”, page 31
.
13 - Bolt
❑ 12 Nm
❑ Quantity: 2
1.2
Overview - Release Cable
1 - Release Lever
❑ Removing and instal‐
ling. Refer to
.
2 - Bolt
❑ 1.5 Nm
❑ Quantity: 2
3 - Bracket
4 - Expanding Nut
❑ Quantity: 2
5 - Release Cable
❑ From the bracket -3- to
the coupling -7-
6 - Grommet
7 - Coupling
8 - Release Cable
❑ From the coupling -7- to
the lid latch -9-
9 - Latch
❑ Removing and instal‐
ling. Refer to
10 - Bolt
❑ Quantity: 2
❑ Tightening specification
-item 13-
1.3
Hood, Removing and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
Removing
– Remove the spray nozzles -4-. Refer to ⇒ Electrical Equip‐
ment; Rep. Gr. 92 ; Windshield Washer System; Spray Noz‐
zles, Removing and Installing .
– Remove the line -5- from the hood opening -1-.
– If equipped, remove the caps -3-.
– Loosen the left and right hex nuts -2- from the hinge -6- (do
not remove the nuts).
A second technician is required for the rest of the removal pro‐
cedure.
– Remove the gas-filled strut. Refer to
⇒ “1.12 Gas-Filled Strut, Removing and Installing”,
– Remove the hex nuts -2- and lift the hood -1- out of the hinges
-6-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст