Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 328
– Remove the bolts -2-.
– Loosen the mirror frame -1- from the catches and remove
rearward.
Installing
Install in reverse order of removal while paying attention to the
following:
– Perform a function test.
Tightening Specifications
8
Wheel Housing Liner
⇒ “8.1 Overview - Front Wheel Housing Liner”, page 445
⇒ “8.2 Overview - Rear Wheel Housing Liner”, page 446
⇒ “8.3 Overview - Sill Panel Cover”, page 447
⇒ “8.4 Front Wheel Housing Liner, Removing and Installing”, page
447
⇒ “8.5 Rear Wheel Housing Liner, Removing and Installing”, page
8.1
Overview - Front Wheel Housing Liner
Note
♦
Depending on the model version, slight deviations of the front wheel housing liner must be considered when
removing and installing.
♦
The illustration shows the left side. The procedure for the right side is identical.
1 - Front Wheel Housing Liner
❑ PP/EPDM material
❑ Removing and instal‐
ling. Refer to
2 - Bolt
❑ 2 Nm
❑ Quantity: 7 on each side
3 - Wheel Housing Liner Front
Section
❑ PP/EPDM material
❑ With cover
❑ There are different ver‐
sions. Refer to the Parts
Catalog for the alloca‐
tion.
4 - Bolt
❑ 2 Nm
❑ Quantity: 6 on each side
5 - Expanding Nut
❑ Quantity: 7 on each side
8.2
Overview - Rear Wheel Housing Liner
Note
♦
The rear wheel housing liner may differ slightly depending on the model.
♦
The illustration shows the left side. The right side is identical.
1 - Rear Wheel Housing Liner
❑ PP/EPDM material
❑ Removing and instal‐
ling. Refer to
.
2 - Bolt
❑ 2 Nm
❑ Quantity: 10 on each
side
3 - Expanding Nuts
❑ Quantity: 2 on each side
4 - Expanding Nut
❑ Quantity: 3 on each side
❑ Gas-tight
DANGER!
Check the gas-tight ex‐
panding nuts for damage
and replace them if nec‐
essary
The expanding nuts seal
off the vehicle interior
from exhaust gas and
must always be replaced
if they are damaged.
5 - Adapter
❑ Only on the right side.
❑ Only on vehicles with a
diesel engine
❑ Install before installing the rear wheel housing liner -1-.
6 - Rear Longitudinal Member
8.3
Overview - Sill Panel Cover
Note
The illustration shows the left side. The right side is identical.
1 - Sill Panel Cover
❑ Removing
– Rear wheel housing lin‐
er, detaching. Refer to
– Remove the screws -2-
and remove the sill pan‐
el cover downward.
❑ Installing
Note
Check the expanding nut for dam‐
age and replace if necessary.
– Position the sill panel
cover.
– Install the bolts -2- and
tighten.
2 - Bolt
❑ 2 Nm
❑ Quantity: 3
3 - Expanding Nut
❑ Quantity: 3
8.4
Front Wheel Housing Liner, Removing
and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Note
♦
The following describes the removal and installation of the left front wheel housing liner. The right side is
identical.
♦
Depending on the model version, slight differences must be considered when removing and installing.
♦
For a better view of the screws, the wheel is not shown in the illustration.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст