Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 229
– Install the release lever. Refer to
⇒ “1.7 Hood Release Lever, Removing and Installing”,
.
– Before closing the hood, make sure the hood release lever and
the release cable are working correctly.
2
Rear Lid
⇒ “2.1 Overview - Rear Lid”, page 49
⇒ “2.2 Rear Lid, Removing and Installing”, page 50
⇒ “2.3 Rear Lid, Adjusting”, page 55
⇒ “2.4 Adjusting Buffer, Removing and Installing”, page 56
⇒ “2.5 Adjusting Buffer, Adjusting”, page 57
⇒ “2.6 Latch, Removing and Installing”, page 58
⇒ “2.7 Actuator, Removing and Installing”, page 60
⇒ “2.8 Hinges, Removing and Installing”, page 64
⇒ “2.9 Catch, Removing and Installing”, page 66
⇒ “2.10 Catch, Adjusting”, page 67
⇒ “2.11 Rear Lid Seal, Removing and Installing”, page 68
⇒ “2.12 Gas-Filled Strut, Removing and Installing”, page 70
⇒ “2.13 Gas-Filled Strut, Venting”, page 72
2.1
Overview - Rear Lid
1 - Rear Lid
❑ Removing and instal‐
ling. Refer to
❑ Adjusting. Refer to
.
2 - Latch
❑ Removing and instal‐
ling. Refer to
.
3 - Bolts
❑ 20 Nm
❑ Quantity: 2
4 - Hinge
❑ Left and right
❑ Removing and instal‐
ling. Refer to
5 - Adjusting Buffer
❑ Left and right
❑ Adjusting. Refer to
.
6 - Ball Stud
❑ 20 Nm + 45°
7 - Gas-Filled Strut
❑ Removing and installing. Refer to
⇒ “2.12 Gas-Filled Strut, Removing and Installing”, page 70
⇒ “2.13 Gas-Filled Strut, Venting”, page 72
.
8 - Ball Stud
❑ 20 Nm + 45°
9 - Hex Nut
❑ 20 Nm + 45°
❑ Quantity: 1 per hinge
10 - Bolts
❑ 10 Nm
❑ Quantity: 2 per hinge
11 - Rear Lid Seal
❑ Removing and installing. Refer to
⇒ “2.11 Rear Lid Seal, Removing and Installing”, page 68
.
12 - Hex Nut
❑ 20 Nm
❑ Quantity: 2
13 - Catch
❑ Removing and installing. Refer to
⇒ “2.9 Catch, Removing and Installing”, page 66
.
❑ Adjusting. Refer to
⇒ “2.10 Catch, Adjusting”, page 67
14 - Bolts
❑ 5 Nm
❑ Quantity: 3
15 - Actuator
❑ Removing and installing. Refer to
⇒ “2.7 Actuator, Removing and Installing”, page 60
.
2.2
Rear Lid, Removing and Installing
⇒ “2.2.1 Rear Lid, Removing and Installing, Sedan”, page 50
⇒ “2.2.2 Rear Lid, Removing and Installing, Wagon”, page 53
2.2.1
Rear Lid, Removing and Installing, Se‐
dan
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
Removing
– Remove the rear lid upper trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Luggage Compartment Trim Panels; Rear Lid
Upper Trim Panel, Removing and Installing .
– Remove the rear lid lower trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Luggage Compartment Trim Panels; Rear Lid
Lower Trim Panel, Removing and Installing .
– Remove the high-mounted brake lamp. Refer to ⇒ Electrical
Equipment; Rep. Gr. 94 ; High-Mounted Brake Lamp; High-
Mounted Brake Lamp, Removing and Installing .
– Disconnect the connectors from any electrical components.
– Guide the wires with the rubber grommet -2- out of the rear lid.
Note
The connectors -4- for the wires -2- are located on the C-pillars.
– Loosen, but do not remove, the bolts -5- on the left and right
hinges.
A second technician is required for the rest of the removal pro‐
cedure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст