Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 853
Vehicles with Stone Chip Protection
– Remove the expanding rivets -1-.
– Remove the bolts -2- for the stone chip protection -3-.
– Remove the stone chip protection -3- from the lower trans‐
verse link -4-.
Continuation for All Vehicles
– Remove the nut -1- and the bolt -2-.
– Remove the shock absorber.
Installing
Installation is the reverse of removal, with special attention to the
following:
– For vehicles with a vehicle level sensor, perform the basic set‐
ting for the wheel damping electronics. Refer to Vehicle Diag‐
nostic Tester .
Tightening Specifications
♦ Refer to
⇒ “6.1.2 Overview - Suspension Strut, Shock Absorber and
Spring, Multi-Link Suspension”, page 192
♦ Refer to
⇒ “5.1 Overview - Transverse Link”, page 181
♦ Refer to
⇒ “1.1 Wheel Bolt Tightening Specifications”, page 286
♦ Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Wheel Housing Liner;
Rear Wheel Housing Liner, Removing and Installing .
• Only fasten the shock absorber with the transverse link in the
curb weight position.
6.2.3
Shock Absorber, Removing and Instal‐
ling, Multi-Link Suspension, Right Shock
Absorber
Special tools and workshop equipment required
♦ Torque Wrench 1332 40-200Nm - VAG1332-
♦ Torque Wrench 1410 - VAG1410-
♦ Spring Compressor Kit - Spring Tensioner - VAG1752/1-
♦ Spring Compressor Kit - Spring Retainer with Inserts -
VAG1752/3A-
♦ Spring Compressor Kit - Adapter Blocks - VAG1752/9-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Bolts - Shock Absorber to Body
♦ Bolt - Shock Absorber to Lower Transverse Link
♦ Nut - Shock Absorber to Lower Transverse Link
Removing
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheel.
– Remove the rear wheel housing liner. Refer to ⇒ Body Exte‐
rior; Rep. Gr. 66 ; Wheel Housing Liner; Rear Wheel Housing
Liner, Removing and Installing .
Vehicles with a Vehicle Level Sensor
– Remove the bolts -1-.
– Remove the Left Rear Level Control System Sensor - G76-
-2- bracket.
Vehicles with Adaptive Chassis DCC
– Disconnect the connector -1- from the shock absorber -2-.
– Remove the wire -3- from the shock absorber -2- -arrow-.
Note
If there is moisture in the connector area, blow compressed air on
the contacts on the shock absorber and the connector.
Continuation for All Vehicles
– Position the Spring Retainer with Inserts - VAG1752/3A- -1-
with the Spring Compressor Kit - Adapter Blocks - VAG1752/9-
-2- on the uppermost spring coil -3-.
– Position the Spring Compressor -3- on the Spring Compressor
Kit - Adapter Blocks - VAG1752/9- -2-.
– Insert the lower Spring Retainer with Inserts - VAG1752/3A-
into the spring -4- at the same time.
– Fasten the Spring Compressor -3- to the Spring Compressor
Kit - Adapter Blocks - VAG1752/9- -2-.
1 - Spring Compressor Kit - Spring Retainer with Inserts -
VAG1752/3A-
2 - Spring Compressor Kit - Adapter Blocks - VAG1752/9-
3 - Spring Compressor Kit - Spring Tensioner - VAG1752/1-
4 - Spring
WARNING
Make sure the coil spring is seated correctly in the Spring
Compressor Kit - Spring Retainer with Inserts - VAG1752/3A-
-arrow- (danger of accident).
– Tension the coil spring until the shock absorber is not under
tension.
– Remove the bolts -1- from the shock absorber -2-.
Vehicles with Stone Chip Protection
– Remove the expanding rivets -1-.
– Remove the bolts -2- for the stone chip protection -3-.
– Remove the stone chip protection -3- from the lower trans‐
verse link -4-.
Continuation for All Vehicles
– Remove the nut -1- and the bolt -2-.
– Remove the shock absorber.
Installing
Installation is the reverse of removal, with special attention to the
following:
– For vehicles with a vehicle level sensor, perform the basic set‐
ting for the wheel damping electronics. Refer to Vehicle Diag‐
nostic Tester .
Tightening Specifications
♦ Refer to
⇒ “6.1.2 Overview - Suspension Strut, Shock Absorber and
Spring, Multi-Link Suspension”, page 192
♦ Refer to
⇒ “5.1 Overview - Transverse Link”, page 181
♦ Refer to
⇒ “1.1 Wheel Bolt Tightening Specifications”, page 286
♦ Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Wheel Housing Liner;
Rear Wheel Housing Liner, Removing and Installing .
• Only fasten the shock absorber with the transverse link in the
curb weight position.
6.3
Shock Absorber, Servicing
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Shock Absorber Set - T10001-
♦ Shock Absorber Set - Socket - T10001/1-
♦ Shock Absorber Set - Extension with Counter Holder 1 -
T10001/9-
♦ Commercially available ring spanner insert, such as »Hazet
6630c-21«
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Nut - Shock Absorber Mount to Shock Absorber
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст