Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 854
1 - Shock Absorber
❑ Removing and instal‐
ling. Refer to
.
❑ Always vent and drain
faulty shock absorbers
before disposal.
❑ Removed shock ab‐
sorber, checking
2 - Protective Tube
3 - Stop Buffer
4 - Shock Absorber Mount
5 - Nut
❑ 25 Nm
❑ Replace after removal
❑ Loosening and tighten‐
ing. Refer to
6 - Cover
Loosening and Tightening Bolted Connection for Shock Absorber
Mount
1 - Commercially available ring spanner insert, such as “Hazet
6630c-21”
2 - Shock Absorber Set - Extension with Counter Holder 1 -
T10001/9-
3 - Ratchet (commercially available)
4 - Torque Wrench 1331 5-50Nm - VAG1331-
5 - Shock Absorber Set - Socket - T10001/1-
6 - Shock absorber mount
Installation is the reverse of removal, with special attention to the
following:
– Slide the protective pipe -1- onto the shock absorber mount
-2-.
– Install and tighten the cable tie -3-.
Note
The closure -arrow- of the cable tie -3- must be in area -a-.
Tightening Specifications
♦ Refer to
⇒ “6.3 Shock Absorber, Servicing”, page 200
6.4
Spring, Removing and Installing
⇒ “6.4.1 Spring, Removing and Installing, Torsion Beam Axle”,
page 202
⇒ “6.4.2 Spring, Removing and Installing, Multi-Link Suspension”,
6.4.1
Spring, Removing and Installing, Tor‐
sion Beam Axle
Special tools and workshop equipment required
♦ -VAG1752/1-
♦ -VAG1752/3A-
♦ -VAG1752/9- , not illustrated
Removing
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheel.
– Remove the clip -1- in the direction of -arrow- until stop.
– Insert the Spring Tensioner -1-.
1 - -VAG1752/1-
2 - -VAG1752/3A-
WARNING
Make sure the coil spring is seated correctly in the -
VAG1752/3A- -2- (danger of accident).
– Tension the coil spring and remove it.
Note
Use a wrench or a reversible ratchet to tighten the spring com‐
pressor.
Installing
Install in reverse order of removal. Note the following:
– Make sure the washer is not damaged.
– Replace the washer if necessary.
– Install the washer on the coil spring.
The spring start -arrow- must touch the stop of lower spring sup‐
port.
– Install the spring and the spring support.
– Spring seat has a pin on bottom.
– Insert this pin into the torsion beam axle opening.
– Insert the top of the spring support into the upper spring end.
– The bead on the spring support -arrow- must fit into the coil
spring correctly.
– Release the tension on the spring, guiding upper spring sup‐
port onto tab of body.
– Remove the Spring Compressor .
– Press in the clip -1- in the reverse direction of -arrow- until stop.
Tightening Specifications
♦ Refer to
⇒ “1.1 Wheel Bolt Tightening Specifications”, page 286
6.4.2
Spring, Removing and Installing, Multi-
Link Suspension
Special tools and workshop equipment required
♦ Tensioning Strap - T10038-
♦ Torque Wrench 1332 40-200Nm - VAG1332-
♦ Torque Wrench 1410 - VAG1410-
♦ Spring Compressor Kit - VAG1752-
♦ Engine and Gearbox Jack - VAS6931- or Engine and Gearbox
Jack - VAG1383A-
Removing
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheel.
– Secure both sides of the vehicle on the hoist arms using -
T10038- .
1 - -T10038-
WARNING
The vehicle could slide off the hoist if it is not secured.
Vehicles with Level Control System Sensor
– Remove the bolts -1-.
– Remove the Left Rear Level Control System Sensor -2- brack‐
et.
Continuation for All Vehicles.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст