Volkswagen Jetta / Jetta Hybrid. Manual — part 56
Note
The right side is shown. The left side is similar.
1 - Door window
❑ Removing and installing
⇒ page 221
2 - Fixed door window
❑ Removing and installing
⇒ page 232
3 - Bolt
❑ Qty. 2.
❑ Specified torque: 5.5
Nm
4 - Window regulator
❑ Removing and installing
⇒ page 227
5 - Nut
❑ Qty. 2.
❑ Specified torque: 8 Nm
6 - Window regulator motor
❑ Removing and installing
⇒ page 225
7 - Bolt
❑ Qty. 3.
❑ Specified torque: 4 Nm
8 - Spreader plug with spread‐
er pin
❑ For fastening the door
window -1-
❑ Always renew when
working on door window
-1-.
9 - Window channel
❑ Removing and installing
⇒ page 230
10 - Retaining clip
3.3
Removing and installing door window
Note
♦
Removal and installation are described only for the right door
window. The removal and installation of the left door window
is similar.
♦
Do not bend the window slot seals when lifting off!
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
3. Rear door window
221
gr. 70 ; Door trim .
– Lower door window -6- as far as stop.
Note
♦
If this part of the work cannot be done due to a fault in window regulator motor -7-, the latter can be removed
⇒ page 225
.
♦
The window can then be pushed to required working position.
– Remove window slot inner seal
⇒ page 145
.
– Remove window slot outer seal
⇒ page 148
.
– Remove front part of window channel (at B-pillar)
⇒ page 230
.
– Lever off cap -5-.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
222
– Screw a 5 mm bolt (approx. 70 mm long) in the spreader pin
-4- and pull bolt out of spreader plug -3-.
– Screw an 8 mm bolt (approx. 80 mm long) into spreader plug
-3-.
Note
When screwing bolt into spreader plug, do not apply excessive pressure on plug. It otherwise falls inwards into
door.
– Pull spreader plug -3- out of window regulator guide and thus
out of door window.
– Lift door window -1- upwards out of window regulator -3-
-arrows a-.
– Pull door window -1- upwards at an angle -arrows b- out of
window slot.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
3. Rear door window
223
Note
♦
When installing door window, always renew spreader plug -3- and spreader pin -4-.
♦
Before inserting spreader plug -3- and spreader pin -4-, check window -1- for damage.
Carry out following work:
– Insert and centre spreader plug -3- in the middle with the door
window removed -1- .
– Press spreader pin -4- flush into spreader plug -3-.
– Guide door window -1- into door -2- -arrows a- and insert door
window into slot of window regulator guide -5-.
– With light pressure from above -arrows b-, engage window
-1- in window regulator -5-.
Further installation is performed in the reverse order of removal.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
224
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст