Geely Diagnosis Flow. Manual part — 106
Geely Diagnosis Flow. Manual part - 106
421
Inspection items
Key switch gear Operation
Standard
value
Remark
Note: there must have the vacuum acting on the vacuum booster when the following inspections are made.
ON Pedal
The pedal does not go down
when the left front wheel is
incapable of rotating
Inspection to the normally
closed valve
Tightness of left front
wheel normally open
valve and normally
closed valve
ON
(two valves and the
pump power on
simultaneously)
Pedal
The pedal does not go down
when the left front wheel is
capable of rotating freely
Inspection to normally
open valve
ON Pedal
The pedal does not go down
when the right front wheel is
incapable of rotating
Inspection to the normally
closed valve
Tightness of normally
open valve and
normally closed valve of
front right wheel
ON
(two valves and the
pump power on
simultaneously)
Pedal
The pedal does not go down
when the right front wheel is
capable of rotating freely
Inspection to normally
open valve
ON Pedal
The pedal does not go down
when the left rear wheel is
incapable of rotating
Inspection to the normally
closed valve
Tightness of normally
open valve and
normally closed valve of
rear left wheel
ON
(two valves and the
pump power on
simultaneously)
Pedal
The pedal does not go down
when the left rear wheel is
capable of rotating freely
Inspection to normally
open valve
ON Pedal
The pedal does not go down
when the rear right wheel is
incapable of rotating
Inspection to the normally
closed valve
Tightness of rear right
wheel normally open
valve and normally
closed valve
ON
(two valves and the
pump power on
simultaneously)
Pedal
The pedal does not go down
when the rear right wheel is
capable of rotating freely
Inspection to normally
open valve
422
No.322 ECU code
When replacing HECU or ECU, code new ECU, otherwise ABS warning lamp will flash and the system can not
operate normally.
Code ECU with diagnosis scanner as following procedures:
Connect diagnosis scanner and diagnosis socket
Enter controller code at address (Addresswort eingeben)
Input 01 and press F1 at function select (Funktion anwählen)
Input relevant vehicle code at code input (see ABS elementary diagram MK20,
No.01901, and MK60, No.0004097)
Display input number, press →
Input 01 at function select (Funktion anwählen), press F1
End
423
No.323 Fluid filling and air exhaust
Wet HCU
When equipped with wet HCU, implement fluid filling and air exhaust according to the requirements of normal
brake system after HCU replaced.
Dry HECU
When equipped with dry HECU, after replacing HECU, not only implement fluid filling and air exhaust
according the requirements of normal brake system, but also implement air exhaust to 2
nd
circuit of HECU. The
procedures when operating with diagnosis scanner are as follows:
Implement fluid filling and air exhaust, until there is no bubble in transparent
pipe.
Connect diagnosis scanner and diagnosis socket
At address (Addresswort ein-geben) basic setting, press F1
Ehnter 01 at function select (Funktion anwählen), press F1
Enter 01 at group number input (Anzeigegruppen-nummer eingeben), press F1
Turn to next page
424
Pedal betätigung und halten…
Press brake pedal and hold, hydraulic pump operates, pedal rebound
Pedal 10×betätigung, Ent-lüfterschraube,zu <↑>
Press brake pedal 10 times and tighten the air drain screws on left and right
brake caliper, press ↑
Pedal lösen, VR/ VL, Entlüfter-schraube, auf <↑>
Loose brake pedal, and air drain screws on left and right brake caliper,
press ↑
Repeat step I, II, and III for 7 times.
Teilentlüftung beendet…
Screen display, air exhaust finished, press → and return to function select
menu.
Enter 02 at function select (Funktion anwählen), press F1
End
Continued from previous page
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст