Geely FC. Manual part — 48
Geely FC. Manual part - 48
Assemble two axle shaft gears and their gaskets in differen-
tial shell by sequence, then screw two planetary gears and
their gaskets in differential shell, and put planetary gear shaft,
lastly, assemble a new elastic cylindrical pin liking that shown
in figure.
Assemble differential gear ring by the direction in figure, and
screw connecting bolts of differential.
Assemble speedmeter driving gear by the direction in figure.
Transmission—Disassemble assembly
189
Assemble chosen adjusting gasket in transmission shell.
Spread seal glue on joint surface of shell body liking that shown
in figure.
Screw corresponding bolts liking that shown in figure, its torque
is 29N•m.
Spread anti-loose fastening glue on connecting bolts of re-
verse shaft, and use a new gasket to cover on the bolt, then
tighten reverse shaft on transmission shell, its torque is 29N•m
Assemble shift fixing assemble on transmission shell, its torque
is 37N•m
Transmission—Disassemble assembly
190
Screw support cover of output rear shaft in differential shell until reaching screwing torque that is
40N•m, then put stop disc spring of output shat bearing in support cover of output rear shaft by the
direction in figure, lastly, press down end cover and tighten connecting bolts of end cover, their
torque is 12N•m
Transmission—Assemble the assembly
Transmission
Assemble the assembly
191
Connecting bolt of end cover
End cover
Stop disc spring of output
shaft bearing
Support cover of output
rear shaft
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column
Steering system
Note
1. Notes that are necessary for steering system:
(a) It is necessary to change parts correctly, for they will influence the performance of steering system to
make running danger.
2. Notes that are necessary for SRS airbag:
(a) MR7180 assembles with SRS (auxiliary protection system) such as safety airbag at the side of driver
and safety airbag at the side of passenger.
Maintenance does not accord with correct repair step, this might incur SRS explodes suddenly in
repair term to make heavy accident. Before repairing auxiliary protection system (including
disassembling, assembling, check or change parts), it is necessary to read the notes in SRS chapter
(auxiliary protection system).
Malfunction phenomenon table
Following table could help you find the reason of malfunction. And the number in table is only used for indicat-
ing possible preferred sequence. Please check each part by sequence, if necessary, change this part.
Malfunction phenomenon
Possible malfunction part
Referred page
1.Tyre (tyre pressure is wrong).
109
2.Power steering oil level (low).
200
3.Driving belt (loose).
-
4.Wheel alignment (wrong).
87
Steering is heavy
5.Steering system joint (abraded).
-
6.Lower control arm ball joint (abraded).
99
7.Steering column (bent).
-
8.Power steering oil pump.
203
9.Power steering gear.
205
1.Tyre (tyre pressure is wrong).
109
Return is bad
2.Wheel alignment (wrong).
87
3.Steering column (bent).
-
4.Power steering gear.
205
1.Steering system joint (abraded).
-
2.Lower control arm ball joint (abraded).
99
Clearance is too big.
3.Middle shaft, sliding fork (abraded).
-
4.Front wheel bearing (abraded).
123
5.Power steering gear.
205
1.Power steering oil level (low).
200
2.Steering system joint (abraded).
-
Abnormal noise
3.Power steering oil pump.
203
4.Power steering gear.
205
192
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст