Geely EC718, EC718RV, EC715, EC715RV. Manual part — 117

FE02-0466b

24. Install the intake manifold assembly.

FE02-0465b

25. Install the air-conditioning compressor high and low

pressure connecting pipes.

FE02-0464b

26. Install the engine wiring harness engine compartment

ground cable and tightening bolt.

Engine

Engine Mechanical System JL4G18-D

2-383

FE02-0463b

27. Connect the pre-catalytic and post-catalytic oxygen

sensor wiring harness connectors.

FE02-0462b

28. Connect ECM harness connector.

FE02-0461b

29. Connect the engine wiring harness and floor harness

connectors.

30. Install the battery bracket.

31. Fill the engine coolant.

32. Fill the air-conditioning refrigerant.

33. Connect the battery negative cable.

2-384

Engine Mechanical System JL4G18-D

Engine

2.6.8.14

Cylinder

Head

Assembly

Replacement

Removal Procedure:

FE02-0187b

1.

Disconnect the battery negative cable. Refer to

2.11.8.1

Battery Disconnection

.

2.

Remove the engine plastic shield. Refer to

2.6.8.1

Plastic

Engine Shield Replacement

.

3.

Discharge the engine coolant. Refer to

2.8.8.1

Engine

Coolant Discharge and Filling

.

4.

Remove the throttle body. Refer to

2.6.8.5

Throttle Body

Assembly Replacement

.

5.

Remove the intake manifold assembly. Refer to

2.6.8.6

Intake Manifold Assembly Replacement

.

6.

Remove the exhaust manifold. Refer to

2.7.6.1

Exhaust

Manifold Replacement

.

7.

Remove the ignition coil and ignition wire. Refer to

2.10.8.3

Ignition Coil Replacement

.

8.

Remove the cylinder head cover. Refer to

2.6.8.2

Cylinder

Head Cover Replacement

.

9.

Remove the drive belt. Refer to

2.6.8.3

Drive Belt

Replacement

.

10. Remove the engine mounting. Refer to

2.6.8.7

Engine

Mount Replacement

.

11. Remove the timing chain cover. Refer to

2.6.8.9

Timing

Chain Cover Replacement

.

12. Remove the timing chain. Refer to

2.6.8.10

Timing Chain

Replacement

.

13. Remove the fuel rail. Refer to

2.2.8.2

Fuel Injector

Replacement

.

14. Disconnect the coolant temperature sensor wiring

harness connector. Refer to

2.2.8.6

Engine Coolant

Temperature Sensor Replacement

.

15. Remove the camshaft position sensor. Refer to

2.10.8.1

Camshaft Position Sensor Replacement

.

16. Remove the VVT solenoid valve. Refer to

2.2.8.4

VVT

Solenoid Valve Replacement and Filter Cleaning

.

17. Remove the camshaft. Refer to

2.6.8.12

Camshaft

Replacement

.

Engine

Engine Mechanical System JL4G18-D

2-385

18. Remove the radiator inlet and outlet pipes.

FE02-0188b

19. Remove the heater inlet and outlet pipes.

FE02-0189b

20. Remove the small cycle pipes cylinder head retaining

bolts.

1

7

9

6

4

3

5

10

8

2

FE02-0190b

21. Remove the cylinder head bolts according to the

sequence in the graphic.

Note

When the engine is hot, it is prohibited to remove the
cylinder head, as this will cause the cylinder head
distortion.

2-386

Engine Mechanical System JL4G18-D

Engine